Description Of The Product - THOMSON CT390 Bedienungsanleitung

CLOCK RADIO
EN
CT390
3
1
7
4 8 8
19
5
2
10 9 9
11 14 12

DESCRIPTION OF THE PRODUCT

10
1 Main LCD display
11
2 Temperature LCD display
12
SNOOZE
3 Alarm repeat
SENSOR
Time, date and alarm settings/ (in 13 SYNC TEMP
4 SET radio mode) details of the RDS
function
14
Settings mode/radio station
15
5 MODE
storage
16
6 DIMMER Backlight intensity settings
MP3 Connect
17
7 SYNC TIME Time synchronisation using RDS
8 RADIO Switching on/off the radio
18
9 VOLUME Volume settings
19
13 3
20
6
4
5
17
10
15 16 14 18
22
TUNING Radio frequency settings/changing
ADJUST the settings
Function selector for alarm 1
Function selector for alarm 2
Synchronisation of the external
probe
20
Battery compartment
USB socket: USB charger
21
Power outlet
22
Auxiliary audio source input
Auxiliaire IN
23
FM antenna
Loudspeaker
USE
INSTALLATION
• Plug the mains adaptor into the socket.
• Insert the mains adaptor plug in the power connector at
the back of the device.
• Only use the adaptor provided. If you wish to
use another adaptor, ensure that it has the same
21
specifications and complies with current standards.
SETTING THE TIME AND DATE
Automatic configuration:
After connecting the device, the radio is off; press SYNC
TIME to automatically configure the clock using RDS
frequencies. If this is not possible due to poor frequency
reception, you can configure the clock manually.
Manual configuration:
• Press SET: the hours display flashes the (clock set).
• Turn the TUNING/ADJUST wheel to set the hours.
• Press MODE to set the minutes.
• Turn the TUNING/ADJUST wheel to set the minutes.
• Press MODE to change the date.
• Turn the TUNING/ADJUST wheel to set the current
year.
• Press MODE to change the month.
• Turn the TUNING/ADJUST wheel to set the month.
• Press MODE to change the day.
• Turn the TUNING/ADJUST wheel to set the day.
• The settings will be confirmed in 10 seconds.
ON OFF
ALARM 1 AND ALARM 2 SETTINGS
The device has 2 different alarms that can be set on different
23 modes (BUZZ, RADIO, WEEK and WEEKEND).
• Press SET twice: the alarm time display flashes (Alarm1
set).
• Turn the TUNING/ADJUST wheel to set the hours.
• Press MODE to change the minutes.
• Turn the TUNING/ADJUST wheel to set the minutes.
• Press SET: the alarm time display flashes (Alarm2 set).
• Turn the TUNING/ADJUST wheel to set the hours.
• Press MODE to change the minutes.
• Turn the TUNING/ADJUST wheel to set the minutes.
• Press SET to exit the alarm settings.
External temperature thermal
sensor
ACTIVATING AND SELECTING ALARM1 OR ALARM2
MODE
Indicator light
• Press / repeatedly to select the type of alarm
function:
I/O (On/Off)
• BUZZ WEEK: the alarm rings every day of the week.
• BUZZ WEEKEND: the alarm rings every day of the
Battery compartment week, except on weekends.
• RADIO WEEK: the alarm starts the radio every day of
the week.
• RADIO WEEKEND: the alarm starts the radio every day
of the week, except on weekends.
DEACTIVATING THE ALARM Measuring the outdoor temperature:
• To deactivate alarm 1 or alarm 2, press or • Remove the battery compartment cover of the external
repeatedly until the alarm lights turn off. probe.
• Insert 2 LR03 1.5 V batteries, ensuring that the polarity
ALARM REPEAT (SNOOZE) is as indicated.
• Touch or pass your hand over the SNOOZE SENSOR • Set the external probe switch to I: this will switch on the
proximity sensor to stop the alarm. The alarm will red light.
sound every 9 minutes. The word SNOOZE flashes • Replace the battery compartment cover of the external
intermittently until the alarm sounds again. probe.
• Press SYNC TEMP at the back of the device to start
SWITCHING OFF THE ALARM synchronisation. The two dashes at the bottom of the
• Press / to turn off the alarm. It will ring again the screen flash.
next day (after 24 hours). • The synchronisation is finished when the temperature
is displayed.
USING THE RADIO • The temperature of the probe is detected every minute.
The reception of RDS signals depends on the physical
location of the device. An obstacle between the FM Note: the external probe has a maximum range of 20
transmitter and the device can affect radio reception metres.
(furniture, high voltage power cable, etc.).
• Press RADIO to switch on the radio and the LCD screen ADJUSTING THE BRIGHTNESS OF THE DISPLAY
will display the FM frequency. • Press DIMMER to adjust the backlight intensity of the
• Turn the TUNING/ADJUST wheel to search for the two LCD screens.
frequency. The frequency steps are of 0.05 MHz.
• Turn the VOLUME wheel to adjust the volume. USB CHARGER SOCKET
• While the radio is playing, press the SET button • Allows you to charge your Smartphone or MP3 player
repeatedly to display the programme service (PS), battery.
programme type (PTY) and radio text (RT). The
information is available if the RDS is active and there is AUXILIARY IN
adequate signal strength. Allows you to play music from an external audio source on
• Press RADIO to put the device on standby. the radio speakers.
Note: use and position the wire aerial to improve reception • Use a male/male 3.5 mm jack cable (not provided).
of FM signals. • Insert one of the male jack plugs into the MP3 player or
Smartphone device.
SAVING YOUR FAVOURITE RADIO STATIONS • Insert the other male jack plug into the AUX IN input at
• Turn the TUNING/ADJUST wheel quickly to set the the back of the device.
closest radio station. The search automatically stops • Switch the radio on.
once a transmitted radio station is correctly identified. • The music being played on the external audio source is
• To save a station, press and hold the MODE button played on the radio.
for 2 seconds. Repeat these steps to pre-set up to 20
stations.
ACCESSING THE MEMORISED STATIONS
When the radio is switched on:
• Press the MODE button repeatedly to go from one
saved station to another (P01 to P20).
INDOOR AND OUTDOOR THERMOMETER
Measuring the indoor temperature:
• The device's built-in probe measures the indoor room
temperature. It is permanently displayed at the bottom
of the small LCD screen.