Inhaltsverzeichnis
Werbung
PCU-10 Manual
PELCO Extended Commands
PELCO Extended Command PELCO
Set Preset (01 to 32)
Clear Preset (01 to 32)
Go To Preset (01 to 32)
Flip (180°)
Go To Zero Pan
Set Auxiliary (01 to 08)
Clear Auxiliary (01 to 08)
Remote Reset
Set Zone START/END
Write Character To Screen
(Column 00 to 19)
Clear Screen
Alarm Acknowledge
Zone Scan ON/OFF
Set/Run Pattern
Set Zoom Speed (00 to 03)
Set Focus Speed (00 to 03)
Reset Camera to defaults
Auto-Focus
AUTO/ON/OFF
Auto-Iris
AUTO/ON/OFF
AGC
AUTO/ON/OFF
Adjust Gain
Auto White Balance ON/OFF
Adjust White Balance (R)
Adjust White Balance (B)
Adjust White Balance (M-G)
Set Shutter Speed
Enable Dev.Phase Del.Mode
Adjust Line Lock Phase Delay General
Adjust Auto-Iris Level
Adjust Auto-Iris Peak Value
Query
X = not supported (100ms red "ERROR" LED D23)
Seite 30 von 34
VISCA
TM
Command(s)
Resonse
General
CAM_Memory: Set 0 to 5 (31)
General
CAM_Memory: Reset 0 to 5 (31)
General
CAM_Memory: Recall 0 to 5 (31)
General
CAM_LR_Reverse: ON/OFF
General
Pan-tilt_Drive: Home
General
Relay_Settings: Set_Relay (1 to 8) ON
General
Relay_Settings: Set_Relay (1 to 8) OFF
General
Pan-tilt_Drive: Reset
General
General
1. CAM_Title: ON,
2. CAM_Title: Title Set1/2/3
General
1. CAM_Title: OFF, 2. CAM_Title: Clear
General
General
General
General
Enables VISCA Variable-Speed Zoom
(Speed: 00 to 07) with PELCO Standard
Command Set
General
Enables VISCA Variable-Speed Focus
(Speed: 00 to 07) with PELCO Standard
Command Set
General
CAM_Power: OFF/ON Cycle
AddressSet, IF_Clear
General
CAM_Focus:
Auto ON / Auto ON / Manual
General
CAM_AE:
Full Auto ON / Full Auto ON / Iris Priority
General
CAM_AE:
Full Auto ON / Full Auto ON / Manual
General
CAM_Gain: Direct
PELCO: 0...65535 = VISCA: 0...65535
General
CAM_WB: Auto / Manual
General
CAM_RGain: Direct
PELCO: 0...65535 = VISCA: 0...255
General
CAM_BGain: Direct
PELCO: 0...65535 = VISCA: 0...255
General
General
CAM_Shutter: Direct
PELCO: 0...65535 = VISCA: 0...255
General
General
General
Query
www.gnt.biz
Comments
Position 0 to 5 is using FCB-xxx internal Preset
Memory. Position 6 to 31 is using PCU-10 int.
Preset Memory (only Pan, Tilt, Relays, Zoom)
Pan, Tilt Home Position
only with GNT DCP-xx
only with GNT DCP-xx
X
max. 20 characters with modern FCB-xxx
PCU-10 EEPROM Write Access!
PCU-10 EEPROM Write Access!
X
X
X
Standard-Speed Zoom Commands can be re-
enabled with Power OFF/ON Cycle or Command
"Reset Camera to defaults"
Standard-Speed Focus Commands can be re-
enabled with Power OFF/ON Cycle or Command
"Reset Camera to defaults"
PCU-10 Reset, VISCA: CAM_Power OFF/ON
Cycle, AddressSet, IF_Clear
Auto-Focus must be switched OFF before using
the "Focus Far/Near" Commands
Auto-Iris must be switched OFF before using the
"Iris Open/Close" Commands
If AGC is switched OFF, the SONY FCB-xxx is
in CAM_AE Manual Mode (Manual Iris, Manual
Shutter and Manual Gain)
AGC must be switched OFF before using the
"Adjust Gain" Command.
VISCA Output: 81 01 04 4C 0Z 0Z 0Z 0Z FF*
(ZZZZ = Gain: 0...65535)
VISCA Output: 81 01 04 43 00 00 0p 0q FF*
(pq = R Gain: 0...255)
VISCA Output: 81 01 04 44 00 00 0p 0q FF*
(pq = B Gain: 0...255)
X
AGC must be switched OFF before using the
"Set Shutter Speed" Command.
VISCA Output: 81 01 04 4A 00 00 0p 0q FF*
(pq = Shutter Speed: 0...255)
X
X
X
X
-
PELCO Resp. ASCII Text: "PCU10 x.x yyy z"
"x.x" = PCU-10 Firmware Version
"yyy" = PELCO Address ("000...255")
"z" = number of detected VISCA Devices (0...7)
Stand: V1.02 Februar 2015 – ab Firmware V1.0
GNT
*hex
*hex
*hex
*hex
Werbung
Inhaltsverzeichnis
