Fitting The Grass Box; Adjusting The Cutting Height; Operation; Information On Correct Mowing - Conino Lamborghini EL 3816 TL Originalbetriebsanleitung

Before operating the machine
The lawn mower is supplied in a pre-assembled state.
Follow the assembly instructions step by step, and use
the diagrams provided as visual guide on how to assem-
ble the machine safely.
a) Assembling the handle
- Remove the machine from the packaging.
- Undo the thumb screws (11) – do not unscrew com-
pletely. Fold back the bottom part of the handle (5) and
tighten the thumb screws (11) on the brackets by hand
(see Fig. 3).
- Open the quick-release lever (10) and fold up the top
part of the handle (6). Close the quick-release lever
(10) to fasten the handle in place, by applying gentle
pressure (if necessary undo or tighten the wingnut (9)
slightly).
If necessary, attach the cable to the handle with the cable
clips (14) (Fig. 6).
b) Fitting the grass box
Assembly of Grass box
Take the components and mount the grass cover handle
(12) (Fig. 7 and 8).
Lift the safety guard (13) (Fig. 9). Locate fully assembled
grass box onto location points at the rear of the deck (Fig.
10).
c) Adjusting the Cutting Height
Important!
Adjust the cutting height only when the engine is switched
off and the power cable has been disconnected.
Before you begin to mow, check to ensure that the blade
is not blunt and that none of the fasteners are damaged.
To prevent any imbalance, replace blunt and/or damaged
blades. To carry out this check, first switch off the motor
and pull out the power plug.
Height of cut is adjusted by raising or lowering the Front
and Rear wheels.
Confirm lock and simultaneously set the required height
by either pulling or pressing on the lever (15). When re-
leasing the lock, the setting selected snaps into place.
There are six heights of cut on this product.
NOTE
A medium height of cut is recommended for most lawns.
The quality of your mowing will suffer and collection will
be poor if you cut too low.
Position
1
2
3
4
5
6
GB | Operating Instruction
(Fig. 2 to 5)
(Fig. 7 to 10)
(Fig. 11)
Cutting depth
70 mm
58 mm
48 mm
38 mm
28 mm
20 mm

Operation

Before you connect the equipment to the mains supply
make sure that the data on the rating plate are identical
to the mains data. Connect the plug (Fig.1/Item 1) to an
extension cable. It is imperative to secure the extension
cable with the cable grip as shown in Figure 1-item 4.
Important!
To prevent the machine switching on accidentally, the
lawn mower is equipped with a safety lock-off (Fig. 12/
Item B) which must be pressed before the switching
bar (Fig. 12/Item A) can be activated. The lawn mower
switches itself off when the switch is released.
Repeat this process several times so that you are sure
that the machine functions properly.
Before you perform any repair or maintenance work on
the machine, ensure that the blade is not rotating and
that the power supply is disconnected.
Repeat this process several times so that you are sure
that the machine functions properly. Before you perform
any repair or maintenance work on the machine, ensure
that the blade is not rotating and that the power supply
is disconnected.
Important!
Never open the discharge flap if the grass box is being
emptied and the motor is still running. The rotating blade
can cause serious injuries.
Always secure the discharge flap and grass bag care-
fully. Always switch off the motor before you remove
these items.
The safety distance between the blade casing and the
user provided by the guide struts must be maintained at
all times. Take special care when mowing and changing
direction on embankments and slopes. Ensure that you
have a secure surface to stand on, wear shoes with anti-
slip soles that offer good grip, and long trousers. Always
mow across the slope (not in up or down direction).
Do not use the mower on gradients exceeding 15° for
safety reasons.
Take special care when moving backwards and pulling
the lawn mower. Danger of stumbling.
a) Information on correct mowing
We recommend that you mow in overlapping lines. Only
mow with sharp, perfect blades so that the blades of
grass do not fray, making the lawn turn yellow.
To achieve a good cut, guide the lawn mower in lines that
are as straight as possible.
These lines should always overlap by a few centimeters
so that you do not leave any strips. How often you should
mow the lawn depends on how fast the lawn grows. Dur-
ing the main growth period (May – June), mow it twice a
week, and once a week at other times. The cutting height
should be between 4 and 6 cm and the growth before the
next cut should be between 4 and 5 cm. If the lawn grows
longer than this on occasion, do not make the mistake
of cutting to normal length straight away since this will
damage the lawn. Never cut the grass by more than half
6