Menus - Team Electronic Expert-1 Bedienungsanleitung

English
The Expert-1 manages its various functions in different menus. For menu navigation, these
function keys are necessary:
FUNC key (5)
Hold the FUNC key (5) for approximately 2 seconds to open the main menu screen.
rotary channel selector (6)
Make your selection with the channel selectors, either with the microphone's UP/DN keys or
the rotary channel selector.
Confirm your selection by pressing the rotary channel selector.
PF3 key
Return to the prior menu level or, on the main menu screen, leave the menu mode.
PF4 and PF6 keys
Use these keys for up and down navigation in the menu.
The following 5 menus are available:
FUNC Menu
These general settings affect the basic radio operation.
BEEP: warn tone; confirms an entry or a change; On/Off
TOT : time out timer, deactivates transmission automatically after set time; Off / 1-30 min
DIM : brightness of background light; 1-3
VOL : volume levels; 1-56
SQL : squelch; Off / 1-28
ASQ : automatic squelch; 1-9
RFG : Off / Auto / 3-30 in 3-steps
DSP : channel number (CH) or frequency (FRQ) format; the channel number format uses
CH-XX (XX being the actual channel number); with the frequency format, the chan-
nel number is shown in addition on the right side of the frequency.
KEYs : function levels of the multi function keys; each key can manage a maximum of 3
functions (1/2/3). You can activate 2 or 3 functions for the multi function keys. This
feature activates the combination of levels of the programmed functions according
the key programming (see KEY MENU); 1-2-3 / 1-2 / 1-3 / 2-3
SCM : channel scan type;
TI: remains on the scanned channel for a certain time before scanning continues.
SQ: pauses on the scanned channel until the signal ends before it continous.
SCRT: 5 / 10 / 15 / 20 / 25 / 30 seconds
AOP : automatic power-on; On/Off; if the radio is set up in a vehicle, the radio powers up
automatically once the ignition is turned.
SWR : stand wave radio measurement -swr; caution: antenna must have 50 Ohm impedance
After selection of "continue", a short swr test is performed. The value is indicated in the
swr-meter (lower scale S)
Note: best value: 1, values in the red part of the meter will damage the radio.
RST : reset;
Opt: reset of all functions
All: reset of all functions and frequencies
26

MENUS

2 - PUD Menu
These general settings affect all channels unless individual channel settings have been made.
To overrule the individual channel settings of the CHAN MENU with the general settings of
the PUD menu, the setting PD in the PUD menu has to be set ON.
- AM/FM : modulation mode AM/FM
[- PWR : only available with HAM version; tx-power settings: 4 / 8 / 15 W ]
- NB : Noise Blanker; On/Off
- HIC : High Frequency Cut; On/Off
- ROG : Rogerton; Off / 5 presets available; up to 8 sequences can be programmed
via software only
[- SPLSET : only available with HAM version; OFF (no shift) / upper shift + / lower shift -]
[- SPLFRQ : only available with HAM version; frequency shift 5-1000KHz]
- BUSY : busy channel lockout; On/Off
- BOT : PTT-ID DTMF calling sequence at begin of transmission;
Off / DTMF call (select 1 out of a maximum of 16)
- EOT : PTT-ID DTMF calling sequence at end of transmission;
Off / DTMF call (select 1 out of a maximum of 16)
- CALL : DTMF call; Off / DTMF call (select 1 out of a maximum of 16)
3 - CHAN Menu
These settings affect only the individual channel.
01 - PD : activation of the general settings of the PUD MENU
On : the settings of the PUD MENU overrule the CHAN settings
Off : individual settings have priority
02 - SCAN : entry in channel scan list
DEL : channel deactivated for channel scan
ADD : channel activated for channel scan, in the display the blue letter S
is displayed.
03 - RCDT : activation/selection of CTCSS/DCS code for the rx-frequency of the
selected channel.
1. select type of code (CTCSS or DCS)
2. select code (38 CTCSS or 104 DCS)
After selection of the type of code (CTCSS or DCS), keep pushing the
rotary channel selector (10) to open the according code list. Make your
selection, which is automatically confirmed after a few seconds.
OFF : no code
CTC : CTCSS
DCS : DCS
04 - TCDT : activation/selection of CTCSS/DCS code for the tx-frequency of the
selected channel, like 03 -RCDT.
English
27