Team Electronic Expert-1 Bedienungsanleitung Seite 13

English
MEM (memory channels)
This feature is only available in the HAM version. In the cb version the message ERROR
is displayed in red letters.
A maximum of 8 channels can be stored in this separate channel bank.
This function key activates/deactivates the MEM memory bank. If activated, no frequency
band symbol (for ham version: A-J, VFO) will be visible. Instead the symbol MEM (in chan-
nel mode) or Mxx (in frequency mode) will indicate the active MEM mode. Select the MEM
channel with the channel selector function.
For manual storage, select the channel on the permitted frequency band and hold the
MEM key until the symbol CH-01 appears (the memory channel number 01 is blue). Now,
select the MEM channel where you would like to store the channel and hold the MEM key
again for confirmation. If the selected MEM channel has not been programmed yet, the
number will blink. If it has been programmed before, the number will not blink.
Please note: the modes MEM and EMG will exclude each other, i.e. while in MEM or EMG
mode, the other mode cannot be activated.
HIC (High Cut frequency filter)
Activates the high frequency filter. This feature can improve the signal quality if high fre-
quency interferences are present.
PF4
VOL (volume)
Activates the volume adjustment. Please select a value between 1-56 with the channel
selectors. For best setup of volume level, deactivate the squelch shortly. The typical fre-
quency noise will be audible.
BND (frequency norm selection)
This feature is only available in the HAM version. In the cb version, the message ERROR is dis-
played in red letters. The according symbol will indicate the selected band (A-J).
Each frequency bank can be programmed with a maximum of 40 channels. In addition, the VFO
mode allows to set any frequency within the frequency range based on the frequency step.
For the frequency norm selection of the cb version, hold the menu key FUNC (8) while
powering the radio on. In the display will show: CB FREQ - Select Band: xx BAND (xx
stands for the actual frequency norm). Select a norm and confirm your selection by pus-
hing the rotary channel selector (10) until the radio switches to regular operation mode.
These frequency norms are available:
EU : 40 FM (26.965-27.405 MHz), 4 W / 40 AM (26.965-27.405 MHz), 4 W
CE : 40 FM (26.965-27.405 MHz), 4 W
U (UK) : 40 FM (27.60125-27.99125 MHz), 4 W / 40 FM (26.965-27.405 MHz), 4 W
PL : 40 FM (26.960-27.400 MHz), 4 W / 40 AM (26.960-27.400 MHz), 4 W
I2 : 36 FM (26.855-27.265 MHz), 4 W / 36 AM (26.855-27.265 MHz), 4 W
DE : 80 FM (26.565-27.405 MHz), 4 W / 40 AM (26.965-27.405 MHz), 4W
DF : 27 FM (26.965-27.275 MHz), 4 W / 27 AM (26.965-27.275 MHz), 4 W
note: do not confuse DF with the dutch DeltaFish frequencies.
TSQ (CTCSS/DCS)
This feature is optional and only available with the CTCSS/DCS versions.
For the transmission and reception mode of the individual channels, 38 CTCSS and 104 DCS
codes are available. For selection of a CTCSS/DCS code, please follow these steps:
1. Select the channel that a code should be assigned to.
2. Open the channel menu (3 CHAN MENU), see section MENUS.
3. Select the menu function 3 - RCDT for setting the rx code selection.
4. Select the coding type CTCSS (CTC) or DCS (DCS).
5. Push and hold the rotary channel selector (10) to open code-list.Make your selection
and confirm.
6. Repeat the steps 2-5, this time for the tx code selection (4 - TCDT).
24
PF5
SQL/ASQ (squelch)
Pushing the function key for a long time will switch between the manual squelch SQL and
the automatic squelch ASQ. Depending on your selection, the symbol SQL or ASQ will
be displayed. Pushing the function key shortly, will activate the setting for the selected
squelch type.
settings: ASQ: 1-9 / SQL: Off, 1- 28.
DW (dual watch)
This feature scans two frequencies alternately for a signal.
1. Select the first channel to be scanned.
2. Press the function key. The red-colored symbol D blinks in the display.
3. Select the second channel within 3 seconds. After 2 seconds the setup will be aborted.
4. Press the function key again. The symbol D does not blink but lights in the display. The
radio switches constantly between the two channels. Once a signal has been detected,
the dual watch function pauses and continous based on the scan settings.
5. Deactivate the function by pressing the function key.
SPL (+/- frequency shift for repeater operation)
This feature is only available for the HAM version. The cb version will display the symbol
ERROR in red letters.
For repeater operation, a frequency shift is required. Tx and rx operate on different fre-
quencies.
By pressing the function key repeatedly, these settings are available:
OFF : no frequency shift
+xxxxK : adds set frequency shift to original frequency
-xxxxK : deducts set frequency shift from original frequency
The frequency shift in the range of +/- 5-1000kHz can be set in the menus PD MENU (ge-
neral setting for all channels) or CHAN MENU (individual channel setting).
PF6
SCA (channel scan)
Activates/deactivates the scan function, which searches all channels of the selected fre-
quency band (if activated for scanning) for signals. If a channel is activated for scanning,
the blue symbol S appears in the display. During scanning the symbol S is red.
The settings for scan type ( SCM: TI=time/SQ=carrier), as well as the scan dwell time for
the setting TI (SCRT: 5-30 seconds in 5-second-steps) are available in the menu FUNC.
A channel can be activated for scanning either via software or manually at the radio by
the CHAN MENU (see paragraph about Menus).
CAL (DTMF call transmission)
Via software and manually at the radio, a maximum of 16 different DTMF calls can be
programmed. Each individual channel can use one of these sixteen DTMF calls. By pres-
sing the function key, the DTMF call will be transmitted.
It can be determined if the DTMF code will be displayed during transmission or not.
5K (frequency shift)
This feature is not available.
English
25