Renkforce 1488533 Bedienungsanleitung Seite 4

Operating instructions
Ceiling motion detector 360°
Item no. 1488533
Intended use
The ceiling-mounted motion detector's integrated PIR sensor responds to temperature chan-
ges within the detection range, e.g., when a person enters the detection range.
For this reason, the ceiling-mounted motion detector can be used for monitoring entrances or
staircases.
The ceiling-mounted motion detector's output can be used, for example, for controlling a light or
other powered device. Observe the maximum connected load in the chapter „Technical data".
The ceiling-mounted motion detector is only intended for use in dry interiors, it must not get
damp or wet.
For safety and approval reasons, you may not convert and/or alter the product. If you use the
product for purposes other than those described above, the product may be damaged. Moreo-
ver, the improper use involves risks such as short-circuits, fire, electric shocks, etc. Please read
the operating instructions carefully and do not discard them. If you pass the product on to a third
party, please hand over these operating instructions as well.
This product complies with the applicable national and European regulations. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
Package contents
• Ceiling motion detector
• 2x screws
• 2x dowels
• Operating instructions
Up-to-date operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the
QR code. Follow the instructions on the website.
Explanation of symbols
The lightning symbol inside a triangle is intended to alert you of health hazards, e. g.,
risk of electrical shock.
An exclamation mark in a triangle indicates important instructions in this operating
manual which must be adhered to.
The arrow symbol is used when specific tips and information on handling are provi-
ded.
The product is intended to be installed and used only in dry indoor rooms; it must not
get damp or wet.
The product is designed according to protection Class II (reinforced or double insu-
lation between the mains supply circuit and output voltage; protective insulation)
Observe the operating instructions!
Safety instructions
Please read the operating instructions carefully and pay particular attention to
the safety instructions. We do not assume liability for injuries/material damag-
es resulting from failure to observe the safety instructions and the information
in these operating instructions regarding the proper handling of the product.
Furthermore, in such cases, the warranty/guarantee will be null and void.
Attention, important note!
Only people with relevant electro-technical knowledge and experience should
carry out the installation! *)
If it is installed improperly, you risk:
• your own life
• the life of the user of the electrical system.
If it is not installed properly, you risk severe damage to property, e.g., by fire.
You face the risk of personal liability for personal injury and material damage.
Contact an electrician!
*) Specialist knowledge required for the installation:
For the installation, in particular, the following specialist knowledge is required:
• The applicable „5 safety rules": Switch off power; secure against switching back
on; determine voltage-free status; earthing and short-circuiting; cover or fence off
nearby live parts
• Choose appropriate tools, meters and, if necessary, personal protective equip-
ment
• Evaluation of the measurement results
• Selection of the electrical installation material to ensure the shutdown conditions
• IP protection types
• Installation of the electrical installation material
• Type of mains supply network (TN system, IT system, TT system) and the con-
nection conditions that follow from them (classical earthing, protective earthing,
required additional measures, etc.)
If you do not have the expertise required for the installation, do not connect
and install it yourself, but ask a qualified technician.
a) General
• The unauthorised conversion and/or modification of the product is not allowed for
safety and approval reasons. Never open/dismantle it (apart from the procedures
for installation and connection described in the manual)! It does not contain any
internal parts that need to be adjusted or maintained by you.
• Maintenance, adjustment or repair work may only be carried out by an expert/
authorised service centre, which is familiar with the hazards involved and the re-
levant regulations.
• The ceiling-mounted motion detector is not a toy and should be kept out of the
reach of children! There is danger of a life-threatening electric shock! Install the
ceiling-mounted motion detector out of the reach of children.
• Protect the product from extreme temperatures, direct sunlight, strong vibrations,
high humidity, moisture, combustible gases, vapours and solvents.
• On industrial sites, the accident prevention regulations of the association of the
industrial workers' society for electrical equipment and utilities must be followed!
• Do not leave the packaging material lying around carelessly as it may be a danger
to children.
• Handle the product with care; it can be damaged by impacts, blows or falls even
from a low height.
• If you have doubts about how the product should be operated or how to safely
connect it, consult a trained technician.
• Maintenance, adjustment and repair work may be carried out only by an expert or
a specialist workshop.
• If you have any questions that are not answered in these operating instructions,
please contact our technical customer service or other professionals.
b) Installation/operating location
• The ceiling-mounted motion detector may be installed and used only in dry indoor
spaces; it must not get damp or wet.
• Only use the ceiling-mounted motion detector when it is firmly mounted. However,
never install the ceiling-mounted motion detector on or inside vehicles.
• Do not mount or operate the ceiling-mounted motion detector in rooms, or under
adverse environmental conditions, where combustible gases, vapours or dust are
or may be present! There is a danger of explosion!
• Do not install or attach objects (e.g., decorative material) to the ceiling-mounted
motion detector.
c) Installation, connection
• The product is constructed according to protection class II.
• The ceiling-mounted motion detector may only operate on the mains voltage (see
section „Technical data"). Never try to operate the product at another voltage, as
this will result in the destruction of the product.
• The ceiling-mounted motion detector must not be connected and operated via a
dimmer.
• During installation, all poles must be disconnected from the mains voltage, e.g.,
via RCD. Between the RCD and the product, there must be an appropriately di-
mensioned fuse or circuit breaker (max. 16 A).
• Perform installation and connection only when all supply lines are disconnected
from the mains voltage. Otherwise, there is a risk of a life-threatening electric
shock!
• Do not connect the product to the power supply immediately after it has been
transferred from a cold room into a warm one (e.g., during transport). The conden-
sation that forms might destroy the device. Moreover, there is danger of electric
shock!
Allow the product to reach room temperature. Wait until the condensation has
evaporated. This might take several hours. Only after this should it be installed,
connected to the mains supply and put into use.