Introduction; Device Description; Scope Of Delivery; Intended Use - Zgonc YGL N.G. 2400 Originalbetriebsanleitung

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment
and success.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
Non-compliance of the operating instructions,
Repairs by third parties, not by authorized service
technicians,
Installation and replacement of non-original spare
parts,
Application other than specified,
A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113..
We recommend:
Read through the complete text in the operating in-
structions before installing and commissioning the
device. The operating instructions are intended to
help the user to become familiar with the machine
and take advantage of its application possibilities in
accordance with the recommendations. The operating
instructions contain important information on how to
operate the machine safely, professionally and eco-
nomically, how to avoid danger, costly repairs, reduce
downtimes and how to increase reliability and service
life of the machine.
In addition to the safety regulations in the operating
instructions, you have to meet the applicable regula-
tions that apply for the operation of the machine in
your country. Keep the operating instructions package
with the machine at all times and store it in a plastic
cover to protect it from dirt and moisture. Read the
instruction manual each time before operating the ma-
chine and carefully follow its information. The machine
can only be operated by persons who were instructed
concerning the operation of the machine and who are
informed about the associated dangers. The minimum
age requirement must be complied with.
In addition to the safety requirements in these operat-
ing instructions and your country's applicable regula-
tions, you should observe the generally recognized
technical rules concerning the operation of woodwork-
ing machines.
We cannot accept any liability for damage or acci-
dents which arise due to a failure to follow these in-
structions and the safety instructions.
2. Layout (Fig. 1-4)
1. Rear grip
2. Front grip
3. Front finger guard / Chain break
4. Saw chain
5. SDS system
5a. Outer button
6. Guide bar cover
7. Guide bar
7a. Adjustment plate
8. Rear finger guard
9. Power cable
10. Claw stop
11. Safety lock- button
12. Cable hook
13. ON/OFF switch
14. Oil tank cap
15. Oil gauge
16. Chain wheel
17. Guide bolt
18. Operation/Overload indicator

3. Scope of delivery

Open the packaging and remove the device carefully.
Remove the packaging material as well as the pack-
aging and transport bracing (if available).
Check that the delivery is complete.
Check the device and accessory parts for transport
damage.
If possible, store the packaging until the warranty pe-
riod has expired.
m Attention
The device and packaging materials are not toys!
Children must not be
allowed to play with plastic bags, film and small parts!
There is a risk of swallowing and suffocation!
• 1 Electrical chainsaw
• 1 Manual
• 1 chain
• 1 bar
• 1 bar sheath

4. Intended use

The purpose of the chain saw is to cut branches, tree
trunks and squared timber up to a diameter or thick-
ness corresponding to the bar length used. Depend-
ing on the machine type, a 14", 16" or 18" bar and
chain can be used. Only materials made from wood
may be processed with the chain saw.
Adequate safety equipment as described in the Oper-
ating Manual must be worn during use. Any use other
than those described in the Operating Manual, for ex-
ample tree maintenance inside the tree, is explicitly
excluded.
The user/operator, not the manufacturer, is responsi-
ble for damage or injuries resulting from misuse. Only
GB 26