IKRA Mogatec HSFI 1500 Gebrauchsanweisung Seite 16

use of power tools for purposes other than those
intended for the respective tool may result in dan-
gerous situations.
5) Service
a) Have the power tool serviced by qualified tech-
nical personnel only; repairs should be carried
out using exclusively original spare parts. This
will ensure the safe operation of the power tool.
Safety instructions
Read the operating instructions and act ac-
cordingly. Keep it for general use. Comply with
the safety information and the warning on the
appliance.
• The appliance must be assembled correctly before use.
• Before inserting the plug in the mains socket, make
sure that the socket ratings are correct and corre-
spond to those indicated on the rating label on the
appliance.
• Never move the appliance by pulling at the cables.
• Always disconnect the appliance from the mains sup-
ply before transporting it to other places.
• Always switch off the appliance before disconnecting
any plug and socket connector or extension cables.
• Keep children and pets away. All onlookers should be
kept a safe distance away from the appliance when
it is in use.
• The user is responsible for third parties while working
with the appliance.
• Be careful never to throw snow towards people or
cars, and never allow anyone in front of your snow
thrower.
• People not acquainted with the operating instructions,
children, juveniles who have not yet reached the mini-
mum age for using this appliance, and people under
the influence of alcohol, drugs or medication are not
allowed to use the appliance.
• Only use the appliance for its designed purposes.
• Always use the appliance with the discharge chute
attached.
• Keep hands and feet away from all rotating and mov-
ing parts.
• Never put your hand in the discharge chute or near the
auger to remove snow, sticks or other debris. Blocked
auger can "spring back" when cleared and may cause
personal injury, even with the appliance stopped.
Always use an object such as a long stick or shovel
handle to clear blockages.
• Wear safe, sturdy, nonskid footwear. Ensure that you
have a good a stand, especially on slopes.
• Wear safety glasses, and avoid any loose-fitting cloth-
ing that could get caught in moving parts. Be careful
of long hair.
• Only work in daylight or sufficiently good artificial light.
• In order to start the appliance, the auger must be
completely free to move.
• The use of the appliance is only permitted if the safety
distance provided by the guide bar is complied with.
• Always hold the handle bar firmly and walk, never run.
• Do not overload the appliance by attempting to clear
snow at too fast a rate.
GB | Operating Instruction
• Slow down and turn corners slowly.
• Caution! Auger does not stop immediately after
switching off.
• Always switch off the appliance, disconnect the plug
and wait until the auger stops before carrying out
maintenance or cleaning work.
• Use caution when cleaning or performing mainte-
nance on the appliance. DANGER! Watch your
fingers! Wear gloves!
• It is forbidden to move or modify any of the electrical
and mechanical safety devices.
• The snow can sometimes hide objects that might clog
the chute, or otherwise cause damage. Clear the area
of doormats, sleds, boards, wires and other debris.
• If the appliance strikes a foreign body, examine the ap-
pliance for signs of damage and carry out any neces-
sary repairs before restarting and continuing to work.
• If the appliance should start to vibrate abnormally,
switch off the motor and check for the cause immedi-
ately. Vibration is generally a warning of trouble.
• The appliance should be checked carefully before use.
You should only work with an appliance that is in good
condition. If you notice any defect on the machine that
may cause danger to the operator, do not operate the
appliance until defects are rectified.
• Replace worn or damaged parts for safety. Use only
original spare parts. Parts not produced by manufac-
turer may cause poor fit and possible injury.
Electrical safety
• Design of the connection cable according to IEC
60245 (H 07RN-F) with a core cross-profile section
of at least
- 1.5 mm
- 2.5 mm
• Long and thin connection lines result in a potential
drop. The motor does not reach any longer its maximal
power; the function of the device is reduced.
• Plugs and coupler outlets on connection cables must
be made of rubber, non-rigid PVC or other thermoplas-
tic material of same mechanical stability or be covered
with this material.
• The connector of the connection cable must be
splash-proof.
• When running the connection line observe that it does
not interfere, is not squeezed, bended and the plug
connection does not get wet.
• Wind off completely the cable when using a cable
drum.
• Do not drive the device across the extension cable.
Make sure that it is behind you in a secure position.
Place the cable on a path or area that has already
been thatched.
• Do not use the cable for purposes for which it is not
meant. Protect the cable against heat, oil and sharp
edges. Do not use the cable to pull the plug from the
socket.
• Protect yourself against electric shocks. Avoid touch-
ing earthed parts with your body (e.g. pipes, heating
apparatus, cookers, fridges etc.).
• Regularly check the extension cables and replace
them if they are damaged.
GB-4
2
for cable lengths up to 25 m
2
for cable lengths over 25 m