Me FRS-106 Betriebsanleitung Seite 5

Operating instructions FRS-106
Thank you for purchasing the wireless intercom ringtone system
FRS-106 for up to 6 users. The receiver indicates each call audibly and
visibly.
Legend
1. Receiver
2. Transmitter (6x)
3. Volume button
4. Tune button
5. Reset button
6. Label field
7. Visual display (LED)
8. Loudspeaker
9. Pedestals
10. LED signal for mains unit
11. Plug socket for mains unit
12. Battery compartment
13. Mounting holes
14. Nameplate
15. Bell push-button
TRANSMITTER
Opening the transmitter and inserting the battery
The transmitter has a small slot on its side to open the enclosure.
Insert a screwdriver in the enclosure slot and turn gently to open the
enclosure.
Insert a battery type CR 2032 into the battery holder with the positive
pole facing upward. Then close the enclosure again. The transmitter is
now ready for use. Repeat this procedure for each transmitter.
Mounting the transmitter
Each transmitter may be mounted either by means of the included
double sided adhesive tape or with screws. The transmitter should not
be mounted on metal since this would significantly limit the range.
Provisionally mount and test the transmitter before mounting in its
final position.
Use the pre-punched holes on the back of the enclosure should you
mount the transmitter with screws. These holes are closed ex-factory
to prevent moisture from entering the transmitter should the latter
be mounted using only double-sided adhesive tape. These holes may
simply be pierced with the screw. Screws and dowels are not included
in delivery.
RECEIVER
The receiver may be used as a standing unit or mounted to the wall.
To use as a standing unit, push the feet out of the enclosure in the
direction of the arrow.
For wall mounting, the receiver has two holes at the back to hang
FRS-106_I-Manual_Fin3.indd 5
it from. The two holes are spaced 73 mm apart (hole centre to hole
centre). The heads of the mounting screws should measure between
4 mm and 6 mm to optimally affix the receiver.
Insert batteries / connect power supply (batteries and mains
unit not included in delivery)
Remove the battery compartment cover and insert 3 AA batteries in the
battery compartment, observing correct polarity. Then close the battery
compartment again with the cover. The receiver is now ready to use.
The receiver may alternatively also be operated with a mains unit.
The wall power supply must provide 6 V DC and at least 300 mA. The
coaxial output of the mains unit must have its positive pole in the
centre. Outside diameter of the coaxial connector: 3.5 mm; inside
diameter: 1.5 mm.
Note: Rechargebale batteries not recommended.
Operation
When a transmitter is pressed, the receiver plays a preset tune and the
LED next to the label area on the transmitter flashes. If another trans-
mitter is also pressed, its LED on the receiver will also start flashing. The
LEDs continue flashing until the reset button is pressed on the receiver.
Note:
The transmitter and receivers are hard-coded, i.e. transmitter no. 1
always activates the LED next to label area 1, transmitter 2 activates
the LED next to label area 2, etc. This coding cannot be changed.
Setting the tune
The next tune is played each time the tune button is pressed. This
will then be stored automatically. The tune is always the same for all
transmitters.
Adjusting the volume
The volume setting has three levels. Pressing the volume button reduces
the volume by one level. The volume reverts to maximum again after
the minimum level.
Technical specifications
Transmitter
Operating voltage: 3 Volt DC (battery type: CR 2032)
Quiescent current: < 5 µA
Current when ringing: < 10 mA
Frequency: 433.92 MHz +/- 250 kHz
Receiver
Operating voltage: 4.5 V DC (3 x battery type Mignon; AA) or
6 V DC from mains unit
Quiescent current: < 200 µA
Current when ringing: < 150 mA
Volume: approx. 80 db
Frequency: 433.92 MHz
Range: approx. 200 m (unobstructed)
5
ENGLISH | FRS-106
25.02.13 12:57