Cameo AURO MATRIX 500 Bedienungsanleitung Seite 17

OPERATION / BEDIENUNG / UTILISATION / OPERACIÓN / OBSŁUGA / UTILIZZO
EN
NOTE
When the spotlight is properly connected to the mains, "Software Update Please Wait..." (only for internal purposes) and the CAMEO logo appear
successively on the display during the startup process and resetting of the motors. After this operation, the spotlight is ready for use and changes to
the mode that was previously selected.
MAIN DISPLAY (DMX mode)
In the upper line of the display, the DMX mode (DMX 8Ch, 33Ch, 37Ch, 111Ch) is prominently displayed in the middle of the DMX start address. As
soon as the DMX signal is interrupted, the background colour of the display changes to red, and "No DMX" is displayed; if the DMX signal is present
again, the display switches back to the main display. The display can be rotated by 180° by pressing the + button.
DMX 111Ch
001
Press Mode To Navigate
MAIN DISPLAY (Standalone mode)
In the upper line of the display, "Operating Mode" is prominently displayed in the middle of the Standalone mode (e.g. Static). The display can be
rotated by 180° by pressing the + button.
Operating Mode
Static
Press Mode To Navigate
SETTING THE DMX START ADDRESS (DMX Address)
Pressing the MODE button will take you to the selection menu for system settings. Using the arrow buttons, select the menu item "DMX Address"
(dark background) and confirm by pressing ENTER. The 3 digits which show the DMX start address, change their colour to red, and you can use the
+ and - buttons to select the desired DMX start address. Confirm the process with ENTER and press the MODE button to return to the main display.
System Settings
DMX Address 001
Mode DMX 111CH
Settings
Network Setting
System Info
SETTING THE OPERATING MODE (Mode)
Pressing the MODE button will take you to the selection menu for system settings. Using the arrow buttons, select the menu item "Mode" (dark
background) and confirm by pressing ENTER. The digits which show the operating mode (for example DMX 111CH), change their colour to red, and
you can use the + and - buttons to select the desired operating mode. Confirm the process with ENTER and press the MODE button to return to the
main display.
Operating modes: DMX 08CH, 33CH, 37CH, 111CH, Slave, Auto, Static.
System Settings
DMX Address 001
Mode DMX 111CH
Settings
Network Setting
System Info
DMX MODE (DMX)
Four different DMX modes are available for selection: 8-channel, 33-channel, 37-channel and 111-channel (DMX 08CH, 33CH, 37CH, 111CH). The
setting is made as previously explained in section SETTING OPERATING MODE. You will find tables with the channels of the different DMX modes in
this manual under DMX CONTROL.
Mode DMX 111CH
SLAVE MODE (Slave)
The setting is made as previously explained in section SETTING OPERATING MODE. Connect the slave and the master unit (same model) with a DMX
cable. Enable one of the standalone modes (Auto, Static) in the master unit. Now the slave unit follows the master unit.
Mode Slave
AUTO MODE (Prog1 - Prog8)
The 8 various auto programs consist of a sequence of fixed programmed colour and motion changes.
Pressing the MODE button will take you to the selection menu for system settings. Using the arrow buttons, select the menu item "Mode" (dark back-
ground) and confirm by pressing ENTER. The digits which show the operating mode change their colour to red, and you can use the + and - buttons
to select the desired Auto operating mode. As soon as you confirm with ENTER, the currently selected Auto program is started. Press ENTER again,
then use the + and - buttons to select one of the 8 Auto programs (Prog1 - Prog8) and confirm with ENTER. Now use the arrow buttons to select the
"AutoSpeed" menu item to adjust the program speed as desired. Press ENTER to confirm, and adjust the speed from 000 to 255 by using the + and -
buttons. Confirm with ENTER and press the MODE button 3x to return to the main display.
Mode Auto
Auto Mode
Auto Prog 8
AutoSpeed 225
17