Hearing Protection; Operating Instructions; Radio; Fm Stereo - JGC RRMP 3500 Bedienungsanleitung

OPERATING INSTRUCTIONS

HEARING PROTECTION

To protect your hearing when wearing headphones please follow these simple suggestions:
Reduce the volume before connecting your earphones. Adjust volume slowly when wearing the
earphones.
Do not set the earphones volume too loud. Longer listening at higher volumes may cause
permanent hearing damage.
After adjusting the volume do not increase it. Your hearing adapts to the higher volume, which may
cause hearing damage.
OPERATING INSTRUCTIONS

RADIO

1. Set the function selector (7) to RADIO position.
2. Set the BAND selector (14) to the desired frequency band.
3. Select your favorite radio station with the TUNING control (15); the frequency is displayed on the dial
scale (11).
4. Adjust the volume with the VOLUME control (16).
5. Set the function selector (7) to TAPE position to turn the radio off.

FM STEREO

While listening to FM stereo broadcast the FM STEREO indicator (5) will light up.

ANTENNA

FM : For best reception fully extend and rotate the telescopic antenna (42).
AM : The AM antenna is built-in; adjust the unit for best reception.

CASSETTE OPERATION

INSERT CASSETTE
1. Set the function selector (7) to TAPE (NOR)
position.
2. Press STOP/EJ. (24) to open the
cassette deck.
3. Insert a tape and close the deck manually.
PLAYBACK
1. Set the function selector (7) to TAPE (NOR) position.
2. Insert a tape as described above.
3. Press PLAY (21) to start playback of deck A or press PLAY (26) for deck B. Playback stops
automatically at the end of the tape.
4. Press STOP/EJ. (24) or (29) to stop playback prior to the end of the tape.
FAST FORWARD/REWIND
1. Press REW (22) to activate rewind for deck A or press REW
2. Press F.FWD (23) to activate fast forward for deck A or press F.FWD
3. Press STOP/EJ. (24) or (29) to stop fast forward/rewind.
8
Side A Side B
(27) for deck B.
(23) for deck B.
RECORD (DECK A ONLY)
Press REC (20) to simultaneously activate PLAY (21). If the inserted tape is write-protected both
buttons will not lock in place and no recording is possible.
RECORDING FROM DISC (DECK A ONLY)
1. Set the function selector (7) to CD/MP3 position.
2. Insert a CD.
3. Select the track to be recorded with
4. Press (33).
5. Press STOP/EJ. (24) to open deck A.
6. Insert a blank cassette.
7. Ensure the write protection is not removed.
8. Close the cassette deck.
9. Press REC (20).
10. Press (33) to start CD playback.
11. To pause your recording press PAUSE (25).
12. To resume the recording press PAUSE (25) again.
13. Press STOP/EJ. (24) to stop the recording.
RECORDING FROM RADIO (DECK A ONLY)
1. Set the function selector (7) to RADIO position.
2. Select frequency band and radio station.
3. Insert a blank cassette.
4. Press REC (20).
5. To pause your recording press PAUSE (25).
6. To resume the recording press PAUSE (25) again.
7. Press STOP/EJ. (24) to stop the recording.
RECORDING FROM BUILT-IN MICROPHONE (DECK A ONLY)
1. Set the function selector (7) to TAPE (NOR) position.
2. Insert a blank cassette.
3. Press REC (20) and talk into the built-in microphone MIC (17).
4. Press STOP/EJ. (24) to stop the recording.
ERASE A TAPE
1. Set the function selector (7) to TAPE (NOR) position.
2. Press REC (20) to erase the existing recordings. Ensure only little background noise, as the built-in
microphone MIC (17) is turned on.
DUBBING FROM DECK B TO DECK A
The 2 decks of the unit allow dubbing from tape to tape. Recording is only possible with deck A; deck B
serves only playback purposes. You can dub with normal speed or high speed.
1. Insert the recorded tape in deck B.
2. Insert the tape to be recorded in deck A.
3. Set the function selector (7) to TAPE (HI) or TAPE (NOR) position. TAPE (HI) is used for
high-speed dubbing and TAPE (NOR) for dubbing with normal speed.
4. Press PAUSE (25) and (30) for decks A and B.
5. Press REC (20) for deck A.
6. Press PLAY (26) for deck B and PAUSE
CASSETTE OPERATION
(37) or (38).
(25) for deck A (to start the recording).
9