Seite 1 PCIE-Q170 Full-size PICMG 1.3 CPU Card MODEL: PCIE-Q170 Full-Size PICMG 1.3 CPU Card Supports 6th Generation LGA1151 Intel® Core™ i7/i5/i3, Pentium® or Celeron® CPU, Intel® Q170 Chipset, DDR4, Dual Intel® PCIe GbE, VGA, iDP, USB 3.0, SATA 6Gb/s, mSATA, Intel® AMT and RoHS...
Seite 2 PCIE-Q170 Full-size PICMG 1.3 CPU Card Revision Date Version Changes October 27, 2016 1.00 Initial release Page ii...
Seite 3 PCIE-Q170 Full-size PICMG 1.3 CPU Card Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer.
Seite 4: Manual Conventions
PCIE-Q170 Full-size PICMG 1.3 CPU Card Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.
Seite 5: Inhaltsverzeichnis
PCIE-Q170 Full-size PICMG 1.3 CPU Card Table of Contents 1 INTRODUCTION......................1 1.1 I ......................2 NTRODUCTION 1.2 M ....................3 ODEL ARIATIONS 1.3 F ........................3 EATURES 1.4 C ......................4 ONNECTORS 1.5 D ....................... 5 IMENSIONS 1.6 D ........................
Seite 6 3.2.11 Front Panel Connector................... 27 3.2.12 I C Connector ....................28 3.2.13 Internal DisplayPort Connector ..............29 3.2.14 iRIS-2400 Module Slot (PCIE-Q170-i2-R10 Only) ........30 3.2.15 Keyboard and Mouse Connector ..............30 3.2.16 LAN LED Connectors ..................31 3.2.17 Parallel Port Connector ................32 3.2.18 PCIe Mini Slot....................
Seite 7 (PCIE-Q170- 2-R10 O )........... 71 ETUP ROCEDURE 4.13.1 Managed System Hardware Setup ..............71 4.13.2 Using the IEI iMAN Web GUI................ 71 5 BIOS ..........................74 5.1 I ......................75 NTRODUCTION 5.1.1 Starting Setup....................75 5.1.2 Using Setup ...................... 75 5.1.3 Getting Help.....................
Seite 8 PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.8 CPU Configuration ..................96 5.3.9 SATA Configuration..................98 5.3.10 NVMe Configuration..................99 5.3.11 USB Configuration ..................100 5.3.12 iEi Feature ....................101 5.4 C ......................... 102 HIPSET 5.4.1 System Agent (SA) Configuration ..............103 5.4.1.1 Graphics Configuration................
Seite 9 PCIE-Q170 Full-size PICMG 1.3 CPU Card G HAZARDOUS MATERIALS DISCLOSURE ............142 Page ix...
Seite 10 PCIE-Q170 Full-size PICMG 1.3 CPU Card List of Figures Figure 1-1: PCIE-Q170 ........................2 Figure 1-2: Connectors ........................4 Figure 1-3: PCIE-Q170 Dimensions (mm) ..................5 Figure 1-4: Data Flow Diagram......................6 Figure 3-1: Peripheral Interface Connectors ................17 Figure 3-2: +12V ATX Power Connector Pinout Location ............20 Figure 3-3: Audio Connector Location ..................21...
Seite 11 PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 3-27: TPM Connector Location..................41 Figure 3-28: USB 2.0 Connector Locations ................42 Figure 3-29: USB 2.0 Connector (Type A) Pinout Location............43 Figure 3-30: USB 3.0 Connector Location .................44 Figure 3-31: External Peripheral Interface Connector ..............45 Figure 3-32: Ethernet Connector....................45...
Seite 12 PCIE-Q170 Full-size PICMG 1.3 CPU Card List of Tables Table 1-1: PCIE-Q170 Model Variations..................3 Table 1-2: PCIE-Q170 Specifications ....................9 Table 2-1: Packing List.........................13 Table 2-2: Optional Items......................15 Table 3-1: Peripheral Interface Connectors ................19 Table 3-2: External Peripheral Connectors................19 Table 3-3: +12V ATX Power Connector Pinouts ................20 Table 3-4: Audio Connector Pinouts ..................21...
Seite 13 PCIE-Q170 Full-size PICMG 1.3 CPU Card Table 3-27: TPM Connector Pinouts ...................41 Table 3-28: USB 2.0 Connector Pinouts ..................42 Table 3-29: USB 2.0 Connector (Type A) Pinouts ..............43 Table 3-30: USB 3.0 Connector Pinouts ..................44 Table 3-31: LAN Pinouts ......................45 Table 3-32: USB 3.0 Port Pinouts....................46...
Seite 14 PCIE-Q170 Full-size PICMG 1.3 CPU Card BIOS Menus BIOS Menu 1: Main ........................77 BIOS Menu 2: Advanced ......................78 BIOS Menu 3: Trusted Computing ....................79 BIOS Menu 4: ACPI Configuration ....................80 BIOS Menu 5: AMT Configuration....................81 BIOS Menu 6: Super IO Configuration..................82 BIOS Menu 7: Serial Port n Configuration Menu...............83...
Seite 15 PCIE-Q170 Full-size PICMG 1.3 CPU Card BIOS Menu 31: Save & Exit....................... 116 BIOS Menu 32: Server Mgmt ....................117 BIOS Menu 33: System Event Log ................... 117 BIOS Menu 34: System Event Log ................... 119 Page xv...
Seite 16: Introduction
PCIE-Q170 Full-size PICMG 1.3 CPU Card Chapter Introduction Page 1...
Seite 17: Ntroduction
1.1 Introduction Figure 1-1: PCIE-Q170 The PCIE-Q170 is a full-size PICMG 1.3 CPU card. It accepts a Socket LGA1151 Intel® Core™ i7/i5/i3, Pentium® or Celeron® processor and supports four 288-pin 2133 MHz dual-channel DDR4 DIMM modules up to 64 GB.
Seite 18: Model Variations
PCIE-Q170 Full-size PICMG 1.3 CPU Card 1.2 Model Variations The model variations of the PCIE-Q170 series are listed below. Model No. Supported CPU iRIS-2400 Module Slot PCIE-Q170-R10 6th generation LGA1151 Intel® Core™ i7/i5/i3, Pentium® or Celeron® PCIE-Q170-i2-R10 Table 1-1: PCIE-Q170 Model Variations 1.3 Features...
Seite 19: Connectors
PCIE-Q170 Full-size PICMG 1.3 CPU Card 1.4 Connectors The connectors on the PCIE-Q170 are shown in the figure below. Figure 1-2: Connectors Page 4...
Seite 20: Dimensions
PCIE-Q170 Full-size PICMG 1.3 CPU Card 1.5 Dimensions The main dimensions of the PCIE-Q170 are shown in the diagram below. Figure 1-3: PCIE-Q170 Dimensions (mm) Page 5...
Seite 21: Data Flow
PCIE-Q170 Full-size PICMG 1.3 CPU Card 1.6 Data Flow Figure 1-4 shows the data flow between the system chipset, the CPU and other components installed on the motherboard. Figure 1-4: Data Flow Diagram Page 6...
Seite 22: Echnical Specifications
PCIE-Q170 Full-size PICMG 1.3 CPU Card 1.7 Technical Specifications The PCIE-Q170 technical specifications are listed below. Specification/Model PCIE-Q170 Full-size PICMG 1.3 CPU card Form Factor 6th generation LGA1151 Intel® Core™ i7/i5/i3, Pentium® or CPU Supported Celeron® CPU Intel® Q170 Four 288-pin 2133/1867 MHz dual-channel unbuffered DDR4 Memory SDRAM DIMMs supported (system max.
Seite 23 PCIE-Q170 Full-size PICMG 1.3 CPU Card Fintek F81866D-I Super I/O Controller ITE IT8528E Embedded Controller Watchdog Timer Software programmable supports 1~255 sec. system reset I/O Interface Connectors Audio Connector One audio connector (10-pin header) Chassis Intrusion One 2-pin header Digital I/O...
Seite 24: Table 1-2: Pcie-Q170 Specifications
PCIE-Q170 Full-size PICMG 1.3 CPU Card Two USB 3.0 ports on rear panel Two USB 3.0 ports via internal box header * The Windows® 7 installation media does not include native driver support for USB 3.0. In order to use the USB keyboard USB 3.0...
Seite 25: Packing List
PCIE-Q170 Full-size PICMG 1.3 CPU Card Chapter Packing List Page 10...
Seite 26: Anti-Static Precautions
Only handle the edges of the PCB: Don't touch the surface of the motherboard. Hold the motherboard by the edges when handling. 2.2 Unpacking Precautions When the PCIE-Q170 is unpacked, please do the following: Follow the anti-static guidelines above. Make sure the packing box is facing upwards when opening.
Seite 27: Packing List
NOTE: If any of the components listed in the checklist below are missing, do not proceed with the installation. Contact the IEI reseller or vendor the PCIE-Q170 was purchased from or contact an IEI sales representative directly by sending an email to ales@ieiworld.com.
Seite 28: Optional Items
PCIE-Q170 Full-size PICMG 1.3 CPU Card Quantity Item and Part Number Image Quick installation guide Table 2-1: Packing List 2.4 Optional Items The following are optional components which may be separately purchased: Item and Part Number Image RS-422/485 cable, 200 mm...
Seite 29 LGA1150 cooler kit (1U chassis compatible, 54W) (P/N: CF-1150SF-R10) DisplayPort to HDMI converter board (for IEI iDP connector) (P/N: DP-HDMI-R10) DisplayPort to LVDS converter board (for IEI iDP connector) (P/N: DP-LVDS-R10) DisplayPort to VGA converter board (for IEI iDP connector) (P/N: DP-VGA-R10) Page 14...
Seite 30: Table 2-2: Optional Items
PCIE-Q170 Full-size PICMG 1.3 CPU Card Item and Part Number Image DisplayPort to DVI-D converter board (for IEI iDP connector) (P/N: DP-DVI-R10) DisplayPort to DisplayPort converter board (for IEI iDP connector) (P/N: DP-DP-R10) SATA to IDE/CompactFlash® converter board (P/N: SAIDE-KIT01-R10)
Seite 31: Connectors
PCIE-Q170 Full-size PICMG 1.3 CPU Card Chapter Connectors Page 16...
Seite 32: Peripheral Interface Connectors
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.1 Peripheral Interface Connectors This chapter details all the peripheral interface connectors. 3.1.1 PCIE-Q170 Layout The figure below shows all the peripheral interface connectors. Figure 3-1: Peripheral Interface Connectors Page 17...
Seite 33: Peripheral Interface Connectors
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.1.2 Peripheral Interface Connectors The table below lists all the connectors on the board. Connector Type Label 4-pin Molex power +12V ATX power supply connector CPU12V1 connector Audio kit connector 10-pin header J_AUDIO1 Battery connector...
Seite 34: External Interface Panel Connectors
PCIE-Q170 Full-size PICMG 1.3 CPU Card Connector Type Label RS-232/422/485 serial ports 10-pin box header COM3, COM4 S_ATA1, S_ATA2, SATA 6Gb/s drive connector 7-pin SATA connector S_ATA3, S_ATA4, S_ATA5, S_ATA6, SMBus connector 4-pin wafer SMB1 SPI flash connector 8-pin header...
Seite 35: Nternal Peripheral Connectors
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2 Internal Peripheral Connectors The section describes all of the connectors on the PCIE-Q170. 3.2.1 +12V ATX Power Connector CN Label: CPU12V1 4-pin Molex power connector, p=4.2 mm CN Type: CN Location: See Figure 3-2...
Seite 36: Battery Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 3-3: Audio Connector Location Description Description HDA_SYNC HDA_BIT_CLK HDA_SDOUT HDA_SPKR HDA_SDIN HDA_RST# HDA_VCC HDA_GND HDA_+12V HDA_GND Table 3-4: Audio Connector Pinouts 3.2.3 Battery Connector CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery.
Seite 37: Chassis Intrusion Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 3-4: Battery Connector Location Description VBATT Table 3-5: Battery Connector Pinouts 3.2.4 Chassis Intrusion Connector CN Label: CHASSIS1 2-pin header, p=2.54 mm CN Type: CN Location: F igure 3-5 CN Pinouts: See Table 3-6 The chassis intrusion connector is for a chassis intrusion detection sensor or switch that detects if a chassis component is removed or replaced.
Seite 38: Crt Fw Update Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.5 CRT FW Update Connector CN Label: J_CRTFW1 3-pin header, p=2.00 mm CN Type: CN Location: See Figure 3-6 CN Pinouts: See Table 3-7 The CRT FW update connector is used to update the CRT firmware.
Seite 39: Digital I/O Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 3-7: DDR4 DIMM Socket Locations 3.2.7 Digital I/O Connector CN Label: DIO1 CN Type: 10-pin header, p=2.00 mm CN Location: See Figure 3-8 CN Pinouts: See Table 3-8 The digital I/O connector provides programmable input and output for external devices.
Seite 40: Ec Debug Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.8 EC Debug Connector CN Label: 18-pin header, p=2.00 mm CN Type: CN Location: See Figure 3-9 CN Pinouts: See Table 3-9 The EC debug connector is used for EC debug. Figure 3-9: EC Debug Connector Location...
Seite 41: Fan Connector (Cpu)
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.9 Fan Connector (CPU) CN Label: CPU_FAN1 4-pin wafer, p=2.54 mm CN Type: CN Location: See Figure 3-10 CN Pinouts: See Table 3-10 The fan connector attaches to a CPU cooling fan. Figure 3-10: CPU Fan Connector Location...
Seite 42: Front Panel Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card The fan connector attaches to a system cooling fan. Figure 3-11: System Fan Connector Location Description FANIO +12V (PWM) Table 3-11: System Fan (SYS_FAN1) Connector Pinouts 3.2.11 Front Panel Connector CN Label: F_PANEL1 14-pin header, p=2.54 mm...
Seite 43: I 2 C Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card Function Description Function Description Speaker BEEP_PWR Power LED IPMI ID_LED+ IPMI LED IPMI ID_LED- PWRBTN_SW# Speaker PC_BEEP Power Button EXTRST- HDD LED Reset SATA_LED# Table 3-12: Front Panel Connector Pinouts 3.2.12 I C Connector...
Seite 44: Internal Displayport Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.13 Internal DisplayPort Connector CN Label: 20-pin box header, p=2.00 mm CN Type: CN Location: See Figure 3-14 CN Pinouts: See Table 3-14 The DisplayPort connector supports HDMI, LVDS, VGA, DVI and DisplayPort graphics interfaces with up to 3840x2160 resolutions.
Seite 45: Iris-2400 Module Slot (Pcie-Q170-I2-R10 Only)
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.14 iRIS-2400 Module Slot (PCIE-Q170-i2-R10 Only) CN Label: IPMI1 iRIS-2400 module slot CN Type: CN Location: See Figure 3-15 The iRIS-2400 module slot allows installation of the iRIS-2400 module. Figure 3-15: iRIS-2400 Module Slot Location...
Seite 46: Lan Led Connectors
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 3-16: Keyboard and Mouse Connector Location Description Mouse Data Mouse Clock Keyboard Data Keyboard Clock Table 3-15: Keyboard and Mouse Connector Pinouts 3.2.16 LAN LED Connectors CN Label: LED_LAN1, LED_LAN2 2-pin header, p=2.54 mm...
Seite 47: Parallel Port Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card Description +3.3V LAN1_LED_LINK#_ACT Table 3-16: LAN1 LED Connector (LED_LAN1) Pinouts Description +3.3V LAN2_LED_LINK#_ACT Table 3-17: LAN2 LED Connector (LED_LAN2) Pinouts 3.2.17 Parallel Port Connector CN Label: LPT1 CN Type: 26-pin box header, p=2.54 mm...
Seite 48: Pcie Mini Slot
PCIE-Q170 Full-size PICMG 1.3 CPU Card RPD4 RPD5 RPD6 RPD7 SIO_ACK# SIO_BUSY SIO_PE SIO_SLCT Table 3-18: Parallel Port Connector Pinouts 3.2.18 PCIe Mini Slot CN Label: MPCIE1 PCIe Mini slot CN Type: CN Location: F igure 3-19 CN Pinouts: See Table 3-19 The PCIe Mini slot is for installing a full-size/half-size PCIe Mini expansion card, such as an mSATA SSD or wireless LAN card.
Seite 49: Table 3-19: Pcie Mini Slot Pinouts
PCIE-Q170 Full-size PICMG 1.3 CPU Card Description Description PCIE_WAKE# +3.3V 1.5V MSATA_CLK# MSATA _CLK PLTRST_N +3.3V PLTRST_N +3.3V SATA_RX-/PCIE_RX- SATA_RX+/PCIE_RX+ 1.5V SMB_CLK SMB_DATA SATA_TX-/PCIE_TX- SATA_TX+/PCIE_TX+ USB_DATA- USB_DATA+ +3.3V +3.3V +3.3V CLINK_CLK CLINK_DATA 1.5V CLINK_RST# MSATA_DET +3.3V Table 3-19: PCIe Mini Slot Pinouts...
Seite 50: Power Button
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.19 Power Button CN Label: PWR_SW1 Push button CN Type: CN Location: See Figure 3-20 The on-board power button controls system power. Figure 3-20: Power Button Location 3.2.20 RS-232 Serial Port Connectors CN Label:...
Seite 51: Rs-232/422/485 Serial Port Connectors
PCIE-Q170 Full-size PICMG 1.3 CPU Card Description Description SOUT Table 3-20: RS-232 Serial Port Connector Pinouts 3.2.21 RS-232/422/485 Serial Port Connectors CN Label: COM3, COM4 CN Type: 10-pin box header, p=2.54 mm CN Location: See Figure 3-22 CN Pinouts: See Table 3-21 Each of these connectors provides RS-232/422/485 connections.
Seite 52: Sata 6Gb/S Drive Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card Description Description SOUT Table 3-21: RS-232/422/485 Serial Port Connector Pinouts The user may use the RS-232/422/485 cable to connect to a serial device. The pinouts of the DB-9 connector are listed below. RS-232 Pinouts...
Seite 53: Smbus Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 3-23: SATA 6Gb/s Drive Connector Locations Description Description Table 3-23: SATA 6Gb/s Drive Connector Pinouts NOTE: If the user shorts the mSATA setup jumper (MSATA_SW1) to force the system to enable mSATA device or an mSATA device is detected, the S_ATA6 connector will be disabled.
Seite 54: Spi Flash Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card The SMBus (System Management Bus) connector provides low-speed system management communications. Figure 3-24: SMBus Connector Location Description SMB_DATA SMB_CLK Table 3-24: SMBus Connector Pinouts 3.2.24 SPI Flash Connector CN Label: JSPI1 CN Type: 8-pin header, p=2.54 mm...
Seite 55: Spi Flash Connector, Ec
PCIE-Q170 Full-size PICMG 1.3 CPU Card Description Description SPI_CS SPI_CLK_SW SPI_SO_SW SPI_SI_SW Table 3-25: SPI Flash Connector Pinouts 3.2.25 SPI Flash Connector, EC CN Label: JSPI2 CN Type: 8-pin header, p=2.54 mm CN Location: See Figure 3-26 CN Pinouts: See Table 3-26 The SPI flash connector is used to flash the EC ROM.
Seite 56: Tpm Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.26 TPM Connector CN Label: TPM1 20-pin header, p=2.54 mm CN Type: CN Location: See Figure 3-27 CN Pinouts: See Table 3-27 The TPM connector connects to a TPM module. Figure 3-27: TPM Connector Location...
Seite 57: Usb 2.0 Connectors
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.27 USB 2.0 Connectors CN Label: USB1, USB2, USB3 8-pin header, p=2.54 mm CN Type: CN Location: See Figure 3-28 CN Pinouts: See Table 3-28 The USB 2.0 connectors connect to USB 2.0 devices. Each pin header provides two USB 2.0 ports.
Seite 58: Usb 2.0 Connector (Type A)
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.28 USB 2.0 Connector (Type A) CN Label: USB4 USB Type A CN Type: CN Location: See Figure 3-29 CN Pinouts: See Table 3-29 The USB Type A connector connects to a USB 2.0/1.1 device.
Seite 59: Usb 3.0 Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.2.29 USB 3.0 Connector CN Label: USB3_34 19-pin box header, p=2 mm CN Type: CN Location: See Figure 3-30 CN Pinouts: See Table 3-30 The USB 3.0 connector connects to USB 3.0 devices. This connector provides two USB 3.0 ports.
Seite 60: External Peripheral Interface Connector Panel
PCIE-Q170 Full-size PICMG 1.3 CPU Card 3.3 External Peripheral Interface Connector Panel The figure below shows the external peripheral interface connector (EPIC) panel. The EPIC panel consists of the following: Figure 3-31: External Peripheral Interface Connector 3.3.1 Ethernet Connectors CN Label:...
Seite 61: Usb 3.0 Connectors
3.3.2 USB 3.0 Connectors CN Label: USB3_1, USB3_2 CN Type: USB 3.0 See Figure 3-31 CN Location: CN Pinouts: See Table 3-32 There are two external USB 3.0 connectors on the PCIE-Q170. Description Description VBUS STDA_SSRX_N STDA_SSRX_P GND_DRAIN STDA_SSTX_N STDA_SSTX_P Table 3-32: USB 3.0 Port Pinouts...
Seite 62: Figure 3-33: Vga Connector
PCIE-Q170 Full-size PICMG 1.3 CPU Card Description Description GREEN BLUE HOT PLUG DETECT DDCDA HSYNC VSYNC DDCCLK Table 3-33: VGA Connector Pinouts Figure 3-33: VGA Connector Page 47...
Seite 63: Installation
PCIE-Q170 Full-size PICMG 1.3 CPU Card Chapter Installation Page 48...
Seite 64: Anti-Static Precautions
Electrostatic discharge (ESD) can cause serious damage to electronic components, including the PCIE-Q170. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the PCIE-Q170 or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
Seite 65 This helps to prevent potential ESD damage. Turn all power to the PCIE-Q170 off: When working with the PCIE-Q170, make sure that it is disconnected from all power supplies and that no electricity is being fed into the system.
Seite 66: Socket Lga1151 Cpu Installation
PCIE-Q170 Full-size PICMG 1.3 CPU Card 4.3 Socket LGA1151 CPU Installation WARNING: CPUs are expensive and sensitive components. When installing the CPU please be careful not to damage it in anyway. Make sure the CPU is installed properly and ensure the correct cooling kit is properly installed.
Seite 67: Figure 4-2: Remove Protective Cover
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 4-2: Remove Protective Cover Step 3: Inspect the CPU socket. Make sure there are no bent pins and make sure the socket contacts are free of foreign material. If any debris is found, remove it with compressed air.
Seite 68: Figure 4-3: Insert The Socket Lga1151 Cpu
PCIE-Q170 Full-size PICMG 1.3 CPU Card Step 7: Insert the CPU. Gently insert the CPU into the socket. If the CPU pins are properly aligned, the CPU should slide into the CPU socket smoothly. See Figure 4-3. Figure 4-3: Insert the Socket LGA1151 CPU Step 8: Close the CPU socket.
Seite 69: Socket Lga1151 Cooling Kit Installation
ONLY compatible with captive screw type cooling fans. The cooling kit can be bought from IEI. The cooling kit has a heat sink and fan. WARNING: Do not wipe off (accidentally or otherwise) the pre-sprayed layer of thermal paste on the bottom of the heat sink.
Seite 70: Figure 4-5: Cooling Kit Support Bracket
Do not overtighten the screws. Step 5: Connect the fan cable. Connect the cooling kit fan cable to the CPU fan connector on the PCIE-Q170. Carefully route the cable and avoid heat generating chips and fan blades.Step 0:...
Seite 71: Dimm Installation
PCIE-Q170 Full-size PICMG 1.3 CPU Card 4.5 DIMM Installation To install a DIMM, please follow the steps below and refer to Figure 4-6. Figure 4-6: DIMM Installation Step 1: Open the DIMM socket handles. Open the two handles outwards as far as they can.
Seite 72: Iris-2400 Module Installation (Optional)
To install the iRIS-2400 module, please follow the steps below and refer to Figure 4-7. Figure 4-7: iRIS-2400 Module Installation Step 1: Locate the IPMI module slot. Place the PCIE-Q170 on an anti-static pad. Step 2: Align the iRIS-2400 module with the iRIS module slot. Align the notch on the module with the notch on the iRIS module slot.
Seite 73: Full-Size Pcie Mini Card Installation
PCIE-Q170 Full-size PICMG 1.3 CPU Card 4.7 Full-size PCIe Mini Card Installation The PCIe Mini card slot allows installation of either a full-size or half-size PCIe Mini card. To install a full-size PCIe Mini card, please follow the steps below.
Seite 74: Half-Size Pcie Mini Card Installation
PCIE-Q170 Full-size PICMG 1.3 CPU Card Step 4: Secure the full-size PCIe Mini card. Secure the full-size PCIe Mini card with the retention screw previously removed (Figure 4-10). Step 0: Figure 4-10: Securing the Full-size PCIe Mini Card 4.8 Half-size PCIe Mini Card Installation The PCIe Mini card slot allows installation of either a full-size or half-size PCIe Mini card.
Seite 75: Figure 4-11: Installing The Standoff
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 4-11: Installing the Standoff Step 3: Insert into the socket at an angle. Line up the notch on the card with the notch on the slot. Slide the PCIe Mini card into the slot at an angle of about 20º (Figure 4-12).
Seite 76: System Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 4-13: Securing the Half-size PCIe Mini Card 4.9 System Configuration The system configuration should be performed before installation. 4.9.1 AT/ATX Power Mode Setting The AT and ATX power mode selection is made through the AT/ATX power mode switch which is shown in Figure 4-14.
Seite 77: Clear Cmos Button
PCIE-Q170 Full-size PICMG 1.3 CPU Card 4.9.2 Clear CMOS Button To reset the BIOS, remove the on-board battery and press the clear CMOS button for three seconds or more. The clear CMOS button location is shown in Figure 4-15. Figure 4-15: Clear CMOS Button Location 4.9.3 PCIe x4 Channel Mode Setup...
Seite 78: Pcie X16 Channel Mode Setup
Main BIOS menu (BIOS Menu 1). 4.9.4 PCIe x16 Channel Mode Setup The PCIE-Q170 supports one PCIe x16 interface on the backplane. The PCIe x16 channel mode setup is made through the BIOS menu in “Chipset System Agent (SA) Configuration PEG Port Configuration”.
Seite 79: Flash Descriptor Security Override Jumper
PCIE-Q170 Full-size PICMG 1.3 CPU Card 4.9.5 Flash Descriptor Security Override Jumper The flash descriptor security override jumper (J_FLASH2) allows to enable or disable the ME firmware update. Refer to Table 4-4 and Figure 4-17 for the jumper location and settings.
Seite 80: Usb Power Selection
PCIE-Q170 Full-size PICMG 1.3 CPU Card 4.9.6 USB Power Selection The USB power selection is made through the BIOS menu in “Chipset PCH-IO Configuration”. Use the USB Power SW1 and the USB Power SW2 BIOS options to configure the correspondent USB ports (see Table 4-5) and refer to Table 4-6 to select the USB power source.
Seite 81: Msata Setup
This section outlines the installation of peripheral devices to the onboard connectors. 4.10.1 SATA Drive Connection The PCIE-Q170 is shipped with two SATA drive cables. To connect the SATA drives to the connectors, please follow the steps below. Step 1: Locate the connectors.
Seite 82: Figure 4-19: Sata Drive Cable Connection
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 4-19: SATA Drive Cable Connection Step 3: Connect the cable to the SATA disk. Connect the connector on the other end of the cable to the connector at the back of the SATA drive. See Figure 4-20.
Seite 83: Adding Usb 3.0 Drivers To A Windows 7 Installation Image
PCIE-Q170 Full-size PICMG 1.3 CPU Card Figure 4-20: SATA Power Drive Connection The SATA power cable can be bought from IEI. See Optional Items in Section 2.4. 4.11 Adding USB 3.0 Drivers to a Windows 7 Installation Image The Windows 7 installation media does not include native driver support for USB 3.0. In order to use the USB keyboard or mouse connected to a USB 3.0 port during OS...
Seite 84: Figure 4-21: Windows 7 Usb 3.0 Creator Utility
PCIE-Q170 Full-size PICMG 1.3 CPU Card Step 3: Extract the downloaded file to a temporary folder on a computer where the user has logged in as the administrator. NOTE: The OS version of the computer can be Windows 7, Windows 8.1 or Windows 10.
Seite 85: Intel ® Amt Setup Procedure
® 4.12 Intel AMT Setup Procedure The PCIE-Q170 is featured with the Intel® Active Management Technology (AMT). To enable the Intel® AMT function, follow the steps below. Step 1: Make sure at least one of the memory sockets is installed with a DDR4 DIMM.
Seite 86: Ipmi Setup Procedure (Pcie-Q170-I2-R10 Only)
Step 3: Connect an Ethernet cable to the RJ-45 connector labeled LAN2 (Figure 3-31). 4.13.2 Using the IEI iMAN Web GUI To manage a client system from a remote console using IEI iMAN Web GUI, follow the steps below. Step 1: Obtain the IP address of the managed system.
Seite 87: Figure 4-23: Iei Iman Web Address
PCIE-Q170 Full-size PICMG 1.3 CPU Card a. Copy the Ipmitool.exe file to a bootable USB flash drive. b. Insert the USB flash drive to the PCIE-Q170-i2 c. The PCIE-Q170-i2 boots from the USB flash drive d. Enter the following command: ipmitool 20 30 02 01 03 00 00 (there is a space between each two-digit number) e.
Seite 88: Figure 4-24: Iei Iman Web Gui
Figure 4-24: IEI iMAN Web GUI NOTE: To understand how to use the IEI iMAN Web GUI, please refer to the iRIS-2400 Web GUI user manual in the utility CD came with the PCIE-Q170. The user manual describes each function in detail.
Seite 89: Bios
PCIE-Q170 Full-size PICMG 1.3 CPU Card Chapter BIOS Page 74...
Seite 90: Introduction
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. NOTE: Some of the BIOS options may vary throughout the life cycle of the product and are subject to change without prior notice.
Seite 91: Getting Help
PCIE-Q170 Full-size PICMG 1.3 CPU Card Function Main Menu – Quit and not save changes into CMOS Status Page Setup Menu and Option Page Setup Menu -- Exit current page and return to Main Menu General help, only for Status Page Setup Menu and Option Page...
Seite 92 PCIE-Q170 Full-size PICMG 1.3 CPU Card Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Server Mgmt BIOS Information Set the Date. Use Tab to BIOS Vendor American Megatrends switch between Date Core Version 5.11...
Seite 93: Advanced
PCIE-Q170 Full-size PICMG 1.3 CPU Card The Main menu has two user configurable fields: System Date [xx/xx/xx] Use the System Date option to set the system date. Manually enter the day, month and year. System Time [xx:xx:xx] Use the System Time option to set the system time. Manually enter the hours, minutes and seconds.
Seite 94: Trusted Computing
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.1 Trusted Computing Use the Trusted Computing menu (BIOS Menu 3) to configure settings related to the Trusted Computing Group (TCG) Trusted Platform Module (TPM). Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc.
Seite 95: Acpi Settings
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.2 ACPI Settings The ACPI Settings menu (BIOS Menu 4) configures the Advanced Configuration and Power Interface (ACPI) options. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced ACPI Settings Select the highest ACPI...
Seite 96: Amt Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.3 AMT Configuration The AMT Configuration menu (BIOS Menu 5) allows the Intel® AMT options to be configured. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced Intel AMT [Enabled] Enable/Disable Intel (R)
Seite 97: Super Io Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.4 Super IO Configuration Use the Super IO Configuration menu (BIOS Menu 6) to set or change the configurations for the serial ports and parallel port. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc.
Seite 98: Serial Port N Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.4.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 7) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced Serial Port n Configuration...
Seite 99 PCIE-Q170 Full-size PICMG 1.3 CPU Card IO=3F8h; Serial Port I/O port address is 3F8h and the interrupt IRQ=3, 4, 11 address is IRQ3, 4, 11 Serial Port I/O port address is 2F8h and the interrupt IO=2F8h; address is IRQ3, 4, 11 IRQ=3, 4, 11 IO=3E8h;...
Seite 100 PCIE-Q170 Full-size PICMG 1.3 CPU Card IO=2F8h; Serial Port I/O port address is 2F8h and the interrupt IRQ=3, 4, 11 address is IRQ3, 4, 11 Serial Port I/O port address is 3E8h and the interrupt IO=3E8h; address is IRQ3, 4, 11 IRQ=3, 4, 11 IO=2E8h;...
Seite 101 PCIE-Q170 Full-size PICMG 1.3 CPU Card IO=3E8h; Serial Port I/O port address is 3E8h and the interrupt IRQ=3, 4, 11 address is IRQ3, 4, 11 Serial Port I/O port address is 2E8h and the interrupt IO=2E8h; address is IRQ3, 4, 11 IRQ=3, 4, 11 IO=2D0h;...
Seite 102: Parallel Port Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card IO=2F8h; Serial Port I/O port address is 2F8h and the interrupt IRQ=3, 4, 11 address is IRQ3, 4, 11 Serial Port I/O port address is 3E8h and the interrupt IO=3E8h; address is IRQ3, 4, 11 IRQ=3, 4, 11 IO=2E8h;...
Seite 103: Iwdd H/W Monitor
PCIE-Q170 Full-size PICMG 1.3 CPU Card Parallel Port [Enabled] Use the Parallel Port option to enable or disable the parallel port. Disable the parallel port Disabled Enabled Enable the parallel port EFAULT Device Mode [STD Printer Mode] Use the Device Mode option to select the mode the parallel port operates in.
Seite 104 PCIE-Q170 Full-size PICMG 1.3 CPU Card Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced PC Health Status Smart Fan Mode Select CPU temperature : +40ºC SYS temperature : +36ºC --------------------- CPU_FAN1 Speed : 1416 RPM : Select Screen ↑...
Seite 105: Smart Fan Mode Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.5.1 Smart Fan Mode Configuration Use the Smart Fan Mode Configuration submenu (BIOS Menu 10) to configure fan speed settings. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced Smart Fan Mode Configuration...
Seite 106: Rtc Wake Settings
PCIE-Q170 Full-size PICMG 1.3 CPU Card Auto mode fan slope PWM Use the + or – key to change the Auto mode fan slope PWM value. Enter a decimal number between 1 and 8. 5.3.6 RTC Wake Settings The RTC Wake Settings menu (BIOS Menu 11) enables the system to wake at the specified time.
Seite 107: Serial Port Console Redirection
PCIE-Q170 Full-size PICMG 1.3 CPU Card selected: Wake up date Wake up hour Wake up minute Wake up second After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off. 5.3.7 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 12) allows the console redirection options to be configured.
Seite 108 PCIE-Q170 Full-size PICMG 1.3 CPU Card Console Redirection [Disabled] Use Console Redirection option to enable or disable the console redirection function. Disabled the console redirection function Disabled EFAULT Enabled Enabled the console redirection function The following options are available in the Console Redirection Settings submenu when the Console Redirection option is enabled.
Seite 109 PCIE-Q170 Full-size PICMG 1.3 CPU Card Parity [None] Use the Parity option to specify the parity bit that can be sent with the data bits for detecting the transmission errors. None No parity bit is sent with the data bits.
Seite 110: Legacy Console Redirection Settings
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.7.1 Legacy Console Redirection Settings Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced Legacy Serial Redirection Port [COM1] Select a COM port to display redirection of Legacy OS and Legacy OPROM Messages.
Seite 111: Cpu Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.8 CPU Configuration Use the CPU Configuration menu (BIOS Menu 14) to view detailed CPU specifications or enable the Intel Virtualization Technology. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced CPU Configuration...
Seite 112 PCIE-Q170 Full-size PICMG 1.3 CPU Card Active Processor Cores [All] Use the Active Processor Cores BIOS option to enable numbers of cores in the processor package. Enable all cores in the processor package. EFAULT Enable one core in the processor package.
Seite 113: Sata Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card Intel TXT(LT) Support [Disabled] Use the Intel TXT(LT) Support option to enable or disable the Intel(R) TXT(LT) support. Disabled Disables Intel® TXT(LT) support EFAULT Enabled Enables Intel® TXT(LT) support 5.3.9 SATA Configuration Use the SATA Configuration menu (BIOS Menu 15) to change and/or set the configuration of the SATA devices installed in the system.
Seite 114: Nvme Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card Hot Plug [Disabled] Use the Hot Plug option to designate the correspondent SATA port as hot-pluggable. Disables the hot-pluggable function of the SATA port. Disabled EFAULT Enabled Designates the SATA port as hot-pluggable. 5.3.10 NVMe Configuration Use the NVMe Configuration (BIOS Menu 16) menu to display the NVMe controller and device information.
Seite 115: Usb Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.11 USB Configuration Use the USB Configuration menu (BIOS Menu 17) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB support.
Seite 116: Iei Feature
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.3.12 iEi Feature Use the iEi Feature menu (BIOS Menu 18) to configure One Key Recovery function. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced iEi Feature Auto Recovery Function Reboot and recover...
Seite 117: Hipset
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.4 Chipset Use the Chipset menu (BIOS Menu 19) to access the PCH IO and System Agent (SA) configuration menus. WARNING! Setting the wrong values for the Chipset BIOS selections in the Chipset BIOS menu may cause the system to malfunction.
Seite 118: System Agent (Sa) Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.4.1 System Agent (SA) Configuration Use the System Agent (SA) Configuration menu (BIOS Menu 20) to configure the System Agent (SA) parameters. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Chipset VT-d...
Seite 119: Graphics Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.4.1.1 Graphics Configuration Use the Graphics Configuration (BIOS Menu 21) menu to configure the video device connected to the system. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Chipset Graphics Configuration Select which of...
Seite 120 PCIE-Q170 Full-size PICMG 1.3 CPU Card DVMT Pre-Allocated [256M] Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the integrated graphics processor when the system boots. The system memory allocated can then only be used as graphics memory, and is no longer available to applications or the operating system.
Seite 121: Peg Port Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.4.1.2 PEG Port Configuration Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Chipset PEG Port Configuration Select PEG Port Link Width as x16 or 2x8 PEG Link Width Configuration [1x16] configuration. PEG 0:1:0...
Seite 122: Memory Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card Max Link Speed [Auto] Use the Max Link Speed option to select the maximum link speed of the PCI Express slot. The following options are available: Auto Default Gen1 Gen2 Gen3 Detect Non-Compliance Device [Disabled] Use the Detect Non-Compliance Device option to enable or disable detecting if a non-compliance PCI Express device is connected to the PCI Express slot.
Seite 123: Pch-Io Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.4.2 PCH-IO Configuration Use the PCH-IO Configuration menu (BIOS Menu 24) to configure the PCH parameters. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Chipset Auto Power Button Status [Disable (ATX)] Select AC power state...
Seite 124: Table 5-2: Bios Options And Configured Usb Ports
PCIE-Q170 Full-size PICMG 1.3 CPU Card USB Power SW1 [+5V DUAL] Use the USB Power SW1 BIOS option to configure the USB power source for the corresponding USB connectors (Table 5-2). Sets the USB power source to +5V +5V DUAL...
Seite 125: Pci Express Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.4.2.1 PCI Express Configuration The PCI Express port number in the PCI Express Configuration menu varies by BIOS (BIOS1 or BIOS2). For detailed information, please refer to Section 4.9.3. For BIOS1: Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc.
Seite 126 PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.4.2.1.1 PCIEX1 Slot/PCIEX4 Slot/MPCIE Slot Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced PCIe Speed [Auto] Select PCI Express port Detect Non-Compliance Device [Disabled] speed. --------------------- : Select Screen ↑ ↓: Select Item Enter: Select +/-: Change Opt.
Seite 127: Hd Audio Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.4.2.2 HD Audio Configuration Use the HD Audio Configuration menu (BIOS Menu 28) to configure the PCH Azalia settings. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Chipset HD Audio Configuration Control Detection of the HD-Audio device.
Seite 128: Ecurity
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.5 Security Use the Security menu (BIOS Menu 29) to set system and user passwords. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Server Mgmt...
Seite 129: Oot
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.6 Boot Use the Boot menu (BIOS Menu 30) to configure system boot options. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Server Mgmt...
Seite 130 PCIE-Q170 Full-size PICMG 1.3 CPU Card Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Normal POST messages displayed Disabled Enabled OEM Logo displayed instead of POST messages EFAULT Launch PXE OpROM [Disabled] Use the Launch PXE OpROM option to enable or disable boot option for legacy network devices.
Seite 131: Ave & Exit
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.7 Save & Exit Use the Safe & Exit menu (BIOS Menu 31) to load default BIOS values, optimal failsafe values and to save configuration changes. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc.
Seite 132: Erver Mgmt (Pcie-Q170- I 2-R10 Only )
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.8 Server Mgmt (PCIE-Q170-i2-R10 Only) Use the Server Mgmt menu (BIOS Menu 32) to configure system event log and BMC network parameters. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Main Advanced...
Seite 133 PCIE-Q170 Full-size PICMG 1.3 CPU Card SEL Components [Enabled] Use the SEL Components option to enable or disable all features of System Event Log during boot. Disabled System Event Log features disabled. System Event Log features enabled. Enabled EFAULT Erase SEL [No] Use the Erase SEL option to select an option for erasing SEL (system event log).
Seite 134: Bmc Network Configuration
PCIE-Q170 Full-size PICMG 1.3 CPU Card 5.8.2 BMC Network Configuration Use the BMC Network Configuration menu (BIOS Menu 34) to configure BMC network parameters. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Server Mgmt BMC network configuration Select to configure LAN...
Seite 135 PCIE-Q170 Full-size PICMG 1.3 CPU Card DynamicBmcDhcp Select to configure LAN channel parameters dynamically by BMC Select to configure LAN channel DynamicBmcNonDhcp parameters dynamically by BIOS Page 120...
Seite 136: Software Drivers
PCIE-Q170 Full-size PICMG 1.3 CPU Card Chapter Software Drivers Page 121...
Seite 137: Vailable Software Drivers
Kernel-Mode Driver Framework (Windows 7 OS only) Intel® Serial IO (Windows 8.1/10 64-bit OS only) 6.2 Software Installation All the drivers for the PCIE-Q170 are on the CD that came with the system. To install the drivers, please follow the steps below. Step 1: Insert the CD into a CD drive connected to the system.
Seite 138: Figure 6-1: Available Drivers
PCIE-Q170 Full-size PICMG 1.3 CPU Card Step 3: A new screen with a list of available drivers appears (Figure 6-1). Figure 6-1: Available Drivers Step 4: Install all of the necessary drivers in this menu. Step 0: Page 123...
Seite 139: A Regulatory Compliance
PCIE-Q170 Full-size PICMG 1.3 CPU Card Appendix Regulatory Compliance Page 124...
Seite 140 PCIE-Q170 Full-size PICMG 1.3 CPU Card DECLARATION OF CONFORMITY This equipment has been tested and found to comply with specifications for CE marking. If the user modifies and/or installs other devices in the equipment, the CE conformity declaration may no longer apply.
Seite 141: B Product Disposal
PCIE-Q170 Full-size PICMG 1.3 CPU Card Appendix Product Disposal Page 126...
Seite 142 PCIE-Q170 Full-size PICMG 1.3 CPU Card CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union–If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
Seite 143: C Bios Options
PCIE-Q170 Full-size PICMG 1.3 CPU Card Appendix BIOS Options Page 128...
Seite 144 PCIE-Q170 Full-size PICMG 1.3 CPU Card Below is a list of BIOS configuration options in the BIOS chapter. 　 System Date [xx/xx/xx] ......................78 　 System Time [xx:xx:xx] .......................78 　 Security Device Support [Disable] ..................79 　 ACPI Sleep State [S3 (Suspend to RAM)]................80 　...
Seite 145 PCIE-Q170 Full-size PICMG 1.3 CPU Card 　 Active Processor Cores [All] ....................97 　 Intel Virtualization Technology [Disabled] ................97 　 Intel(R) SpeedStep(tm) [Enabled]..................97 　 CPU C states [Disabled] ......................97 　 Intel TXT(LT) Support [Disabled]..................98 　 SATA Controller(s) [Enabled] .....................98 　 SATA Mode Selection [AHCI]....................98 　...
Seite 146 PCIE-Q170 Full-size PICMG 1.3 CPU Card 　 Discard Changes and Reset .................... 116 　 Restore Defaults ....................... 116 　 Save as User Defaults ...................... 116 　 Restore User Defaults ...................... 116 　 SEL Components [Enabled]..................... 118 　 Erase SEL [No] ........................118 　...
Seite 147: D Terminology
PCIE-Q170 Full-size PICMG 1.3 CPU Card Appendix Terminology Page 132...
Seite 148 PCIE-Q170 Full-size PICMG 1.3 CPU Card AC ’97 Audio Codec 97 (AC’97) refers to a codec standard developed by Intel® in 1997. ACPI Advanced Configuration and Power Interface (ACPI) is an OS-directed configuration, power management, and thermal management interface. AHCI Advanced Host Controller Interface (AHCI) is a SATA Host controller register-level interface.
Seite 149 PCIE-Q170 Full-size PICMG 1.3 CPU Card DIMM Dual Inline Memory Modules are a type of RAM that offer a 64-bit data bus and have separate electrical contacts on each side of the module. The digital inputs and digital outputs are general control signals that control the on/off circuit of external devices or TTL devices.
Seite 150 PCIE-Q170 Full-size PICMG 1.3 CPU Card LVDS Low-voltage differential signaling (LVDS) is a dual-wire, high-speed differential electrical signaling system commonly used to connect LCD displays to a computer. POST The Power-on Self Test (POST) is the pre-boot actions the system performs when the system is turned-on.
Seite 151: E Digital I/O Interface
PCIE-Q170 Full-size PICMG 1.3 CPU Card Appendix Digital I/O Interface Page 136...
Seite 152: Ntroduction
PCIE-Q170 Full-size PICMG 1.3 CPU Card E.1 Introduction The DIO connector on the PCIE-Q170 is interfaced to GPIO ports on the Super I/O chipset. The digital inputs and digital outputs are generally control signals that control the on/off circuit of external devices or TTL devices. Data can be read or written to the selected address to enable the DIO functions.
Seite 153: Assembly Language Sample
PCIE-Q170 Full-size PICMG 1.3 CPU Card E.2 Assembly Language Sample 1 AX, 6F08H ;setting the digital port as input AL low byte = value AH – 6FH Sub-function: AL – 9 :Set the digital port as OUTPUT :Digital I/O input value E.3 Assembly Language Sample 2...
Seite 154: F Watchdog Timer
PCIE-Q170 Full-size PICMG 1.3 CPU Card Appendix Watchdog Timer Page 139...
Seite 155 NOTE: The following discussion applies to DOS environment. Contact IEI support or visit the IEI website for specific drivers for other operating systems. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash. This condition may have occurred by external EMIs or a software bug.
Seite 156 PCIE-Q170 Full-size PICMG 1.3 CPU Card NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. EXAMPLE PROGRAM: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...
Seite 157 PCIE-Q170 Full-size PICMG 1.3 CPU Card Appendix Hazardous Materials Disclosure Page 142...
Seite 158 PCIE-Q170 Full-size PICMG 1.3 CPU Card The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.
Seite 159 PCIE-Q170 Full-size PICMG 1.3 CPU Card 此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符合中国 RoHS 标准规定的限量要求。本产品上会附有”环境友好使用期限”的标签，此期限是估算这些物质”不会有泄漏或突变”的年限。本产品可能包含有较短的环境友好使用期限的可替换元件，像是电池或灯管，这些元件将会单独标示出来。部件名称有毒有害物质或元素铅汞镉六价铬多溴联苯多溴二苯醚 (Pb) (Hg) (Cd) (CR(VI)) (PBB) (PBDE) 壳体显示印刷电路板金属螺帽电缆组装风扇组装电力供应组装电池 O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T 11363-2006 (现由 GB/T 26572-2011 取代) 标准规定的限量要求以下。...

IEI PCIE-Q170 Bedienungsanleitung

Quicklinks

Verwandte Anleitungen für IEI PCIE-Q170

Inhaltszusammenfassung für IEI PCIE-Q170

Inhaltsverzeichnis