Klingel WRCTK34 Bedienungsanleitung Seite 5

Set Daily Alarm:

Holding S2 (4 o'clock button) while the watch is in the real time mode for more than 5 seconds until the watch says "Set Alarm, Press S1 (2 o'clock button) to
Set"

Press S1, The watch says "Press S1 (2 o'clock button) to Set Hour, S2 (4 o'clock button) to confirm."

Press S1(2 o'clock button) to set alarm hour

Press S2 after Alarm hour is set

The watch says "Press S1 (2 o'clock button) to Set Minute, S2 (4 o'clock button) to confirm."

Press S1(2 o'clock button) to set alarm minute

Press S2 (4 o'clock button) to confirm and Exit after you have set the Alarm minute

After confirmation, the watch will tell the Alarm time (Hour and Minute) that you have been set

To check your alarm time setting, press S2 once while the watch is running normally.
Remarks:

The Alarm will Beep for 30 seconds, you can turn off the alarm with a push of any button

The Alarm is a Daily alarm, so even you turned it off the Beeping sound, the alarm will Beep on the next day again. If you want to turn off the Daily Alarm,
you can follow the Alarm On/Off setting as below.

Every time when a Beep is off, it will speak the Alarm Time.
Alarm ON/OFF:

Holding S2 (4 o'clock button) while the watch is in the normal running mode for more than 5 seconds until the watch says "Set Alarm, Press S1 (2 o'clock
button) to Set."

Press S2 (4 o'clock button) one more time, the watch speaks "Alarm ON/OFF, Press S1 (2 o'clock button)to set"

Press S1 the watch says "Press S1 (2 o'clock button) to On/Off, S2 (4 o'clock button) to confirm."

Press S1 (2 o'clock button)

Every press of S1 (2 o'clock button) switches the alarm from ON to OFF. The watch says, "Alarm On" when it is set to ON or "Alarm OFF" when it is set to
OFF

Press S2 (4 o'clock button)to confirm and Exit
Hourly Announcement (Chime) ON/OFF
(When Chime is ON, the watch announces the "HOUR" every Hour)
(Chime is reset to OFF)

Holding S2 (4 o'clock button) while the watch is in the normal running mode for more than 5 seconds until the watch says "Set Alarm, Press S1 (2 o'clock
button) to Set"

Press S2 (4 o'clock button) 2 more time, the watch says "Chime ON/OFF, Press S1 (2 o'clock button)to set"

Press S1 the watch says "Press S1 (2 o'clock button) to On/Off, S2 (4 o'clock button) to confirm."

Press S1 (2 o'clock button)

Every press of S1 (2 o'clock button) switches the hourly chime alert from ON to OFF. The watch says, "Chime On" when it is set to ON or "Chime OFF"
when it is set to OFF

Press S2 (4 o'clock button)to confirm and Exit

After a Chime alert is confirmed to be ON, the watch will announce "HOUR" every one hour.
Manual Time Setting (for Country without Time signal) :
(You should use this function only when you travel or living in countries with no Time signal. You must set your watch to your local time when you come back from
countries without radio signal or your watch will never be able to pick up signal at 3AM as there is always time different from your country with those countries.)
Set Time

Holding S2 (4 o'clock button)while the watch is in the Time Keeping mode for more than 5 seconds until the watch says: Set Alarm, Press 2 o'clock
button to set

Push S2 4 more times, until the watch says: Set Time, Press 2 o'clock button to set

Press 2 o'clock button (S1)

The watch says: Press 2 o'clock button to set Hour, 4 o'clock button to confirm

Press S1 (2 o'clock button) to set Hour. Listen very carefully to the watch to make sure the right AM or PM has been set.

Press S2 (4 o'clock button) to confirm after you have set the Hour, after pressing S2 (4 o'clock button)

The watch says: Press 2 o'clock button to set Minute, 4 o'clock button to confirm

Press S1 (2 o'clock button) to set Minute

Press S2 (4 o'clock button) to confirm after the minute is set

After confirmation, the watch fast spinning to match the time announcement automatically.

Wait until the watch resume normal running
Your watch is not able to manual set Date, Day, Month and Year. The calendar will be updated after a signal reception is updated.
TROUBLESHOOTING:Your watch is a very delicate and precise instrument. Although uncommon, sometimes hard knocks or vibrations can cause the hands to
move irregularly, and therefore display the incorrect time, although the internal clock is keeping accurate time. You may notice this if when the time announcement
does not match with the position of hands. Then you need to reset watch hands by the following procedures.
Reset Watch Hands

Wait until the second hand just stop at 12 o'clock and pull out the middle crown immediately so that the second hand stops at 12 o'clock position.

Turn the crown to set Hour and Minute hands to 12 o'clock.

After all hands stop at 12:00:00, holding S1 for 5 seconds and then,

Push-in the crown

The watch spins to match the internal time and resume normal running when the time matching is finished. When the watch resume normal running, the
watch hands match with the internal time-keeping of the watch.
5