Inserting The Batteries - Classic smart 1 universal Handbuch

GB
USER INSTRUCTIONS
Classic smart 1 TV/TEXT Universal Remote Control

INSERTING THE BATTERIES.

Your new smart 1 remote control uses 2 LR03 or AAA Alkaline batteries
which must be installed before it can be used. Always use new batteries of
the same type and install the two new batteries the correct way round as
shown by the battery markings in the battery compartment on the back of the
remote control.
Please dispose of used batteries as advised by the battery manufacturer.
SETTING UP YOUR smart 1
Your smart 1 can control TV basic functions incl. Teletext.
It can be set up by entering either a 3 digit code from the code list included in
your instruction book or by using the library search facility. Instructions for
both methods follow.
SET UP BY ENTERING A 3 DIGIT CODE.
Refer to the code list in your instruction book and look up the 3 digit code
which corresponds to the brand of TV you wish to control.
If there is more than one code listed against the brand
start with the first code.
Make a note of the code and follow steps 1 to 5 below.
1) Switch on the TV you wish to control.
2) Press and hold down the STANDBY key on the smart 1 and at the
same time press and hold down the OK key. Keep both keys pressed
down for approximately two seconds until the indicator light on the
STANDBY key being held down lights and remains on. Release both
keys.
3) Use the number keys on the handset to enter the 3 digit code you found
in the code list.
4) Press and release the STANDBY key and the indicator will blink 3 times.
This indicates that you have now stored the code into the handset.
5) Try all of the functions of the remote control.
6) If your device does not respond or responds incorrectly to the
commands repeat steps 1 to 5 using the next number you found against
your brand in the code list.
If the STANDBY key does not blink 3 times at step 4 an incorrect code has
been entered. Check for the correct 3 digit code for your TV in the code
table and repeat steps 1 to 5.
Make a note of the code used on the label inside the battery compartment
for future use.
6
SET UP BY USING THE LIBRARY SEARCH FACILITY.
If you cannot identify the correct code for your TV from the code list use the
code search facility.
1) Switch on the TV you wish to control.
2) Press and hold down the STANDBY key on the smart 1 and at the
same time press and hold down the OK key. Keep both keys pressed
down for approximately two seconds until the indicator light on the
STANDBY key being held down lights and remains on. Release both
keys.
3) Point the smart 1 towards the TV you wish to control and press either
the P up or P down key repeatedly until your TV switches off. The P up
key searches forwards through the library and the P down key searches
backwards through the library. Alternatively hold down the P up or P
down key and the smart 1 will search through each available code at
approximately one-second intervals.
4) When your TV switches off stop pressing the key. Should you
accidentally press the key after your TV has switched off you can back
up by pressing the opposite key.
5) Press and release the STANDBY key and the indicator will blink 3 times.
This indicates that you have now stored the code into the handset.
6) Switch your TV back on and try all of the functions of the remote control.
7) If your TV does not respond correctly to the commands from the remote
control continue the search process until you find a suitable code by
repeating steps 1 to 5. The handset will continue its search from the last
code you selected.
Please be patient when searching by this method as the library contains
a large number of codes and it may take some time to find a suitable
code.
READ OUT THE STORED CODE NUMBER.
Having found a suitable code by the search method it is useful to identify the
code number and record this in the battery compartment for future use.
1) Press and hold down the STANDBY key on the smart 1 and at the
same time press and hold down the OK key. Keep both keys pressed
down for approximately two seconds until the indicator light on the
STANDBY key being held down lights and remains on. Release both
keys.
2) Press and release the MUTE key.
3) The indicator light will then blink the number of the first digit, pause,
blink the number of the second digit, pause and then blink the number
of the third digit. (e.g. 1 blink = digit 1, 6 blinks = digit 6. Note 10 blinks
= digit 0).
4) The handset will then automatically return to normal operation.
Make a note of the code number found above, on the label inside the
battery compartment for future use.
GB
7