Stand-By Indicator; Remote Control; Numeric Keypad - NAD C521i Bedienungsanleitung

During playback, press the SKIP
of the next track on the disc or next programmed track in Program
Play mode. Thus, to sample each song, press PLAY and then tap
SKIP after you've heard a few seconds of each track. From Stop,
press the SKIP
where you want to start playback. Press Play to start playback.

12. STAND-BY INDICATOR

The stand-by indicator turns on in green when the unit is
switched on, and changes to amber when switched to stand-by
mode.

REMOTE CONTROL

A wireless remote control is provided with your compact disc
player, enabling you to operate play-back functions from the
comfort of your chair or from virtually anywhere in the room. For
reliable operation there should be a clear line-of-sight path from
the remote control to the front of the CD player. If the player does
not respond to remote commands, it may be that this line-of-sight
path is obstructed by clothing, paper, or furnishings.
Most of the buttons on the remote control handset have the same
effect as the corresponding buttons on the front panel of the disc
player. In addition the handset is equipped with some extra
buttons and functions, such as the numeric keypad and Program
functions.
POWER ON
Press this Green button to switch on the power to the disc player
from Standby mode. The LED will change from Amber to Green,
and the EFL display will illuminate.
POWER OFF
Press this Red button to switch to Standby mode from power ON
mode. The LED will change from Green to Amber and the
display will go dark.

NUMERIC KEYPAD

Using the direct-entry numeric keypad (1 to 10; +10) causes the
player to jump directly to the beginning of a numbered track and
commence play. Thus to play Track 5, simply press 5. To play
GB
Track 20, press: +10, 10. To play Track 36, press: +10, +10,
+10, 6.
PROGRAM
The C521i CD player allows for programmed playback of up to 20
tracks in any desired order. To engage Program Play with your
desired track sequence in the memory:
1. Press PROGRAM. The "MEMORY" indicator will light up. The
display indicates "Pr p:01", meaning that the player is
awaiting the first Program entry.
2. Use the SKIP or the Direct-Entry Numeric keypad buttons to
select the first track in your planned sequence. The selected
track number will blink in the display.
3. Press PROGRAM to store the selected track number in
memory. The display will revert to show Program-Entry mode
and advance to "Pr p:02", showing that the player is ready for
your second entry.
4. Repeat Steps 2 and 3 to select and store other track numbers
in memory, up to a maximum of 20 entries. The display will
show "FULL" when 20 tracks have been entered.
5. If you want to review or edit your program entries, press
PROGRAM repeatedly to cycle the display through them. When
the highest program number is displayed, you can enter
additional tracks in the memory by repeating Steps 2 and 3.
6
once to skip to the beginning
button until you've reached the track from
6. To play the stored program, press PLAY "MEMORY" will
appear in the display, indicating that a stored program is
being played. During Program Play the SKIP buttons will
access only the tracks in the program list. So if you want to
play only a portion of a stored program, initiate play and
press SKIP to jump over the programmed tracks that you
don't want to hear.
7. To terminate program play, press STOP. However the stored
track list remains in memory; if you want to play the program
again, simply press PLAY again. If you want to edit the program,
press PROGRAM repeatedly to review the list and change. To
add tracks, press the PROGRAM button until the highest
program number is displayed.
8. To clear the program memory, press STOP, OPEN/CLOSE to
open the drawer, or switch off the POWER.
The following example presents a step-by-step illustration of how to
program and start Program Play to play tracks 5, 23, 9, 16, and 1.
While the CD player is stopped:
Press on remote control Display shows
PROGRAM
5
PROGRAM
+10, +10, 3
r p:03
PROGRAM
9
PROGRAM
+10, 6
PROGRAM
1
PROGRAM
PLAY
DELETE
The C521i CD Player allows the user to delete unwanted tracks
in any desired order in either the Program Mode or the Stop
Mode. To Delete tracks, use the sequence of commands below.
In Program Mode:
1. Press DELETE. The display indicates "dE d:01"; the player is
now ready for first Delete entry. "dE" will change to first
memory track after 1 second.
Use the I<<SKIP & SKIP>>I buttons to select the first track
2.
you would like to delete. The track number will flash.
3. Press DELETE again to store the selected track number in
memory. The selected track number will be deleted in the
display. The display will advance to next location. This
showing that the player is ready for your second entry but
cannot delete track above track 25.
4. Repeat Steps 2 and 3 to select the delete the track numbers
in memory, up to a maximum of 20 entries.
5. To play the stored program, just press PLAY. During playing,
the SKIP buttons will access only the tracks still listed. The
deleted songs are not listed.
6. To clear the memory, press STOP twice ,OPEN/CLOSE to
open the drawer, or switch off the power.
In Stop Mode:
1. Press DELETE. The display indicates "dE d:01" with total
track time. The player is ready for the first Delete entry.
2. Use the Direct-Entry Numeric keypad buttons to select the
first track you would like to delete. The selected track
number will be deleted in the calendar display and the
updated total playing time is shown on display.
Pr p:01
5 p:01
Pr p:02
23 p:02
Pr p:03
9 p:03
Pr p:04
16 p:04
Pr p:05
1 p:05
Pr p:06