Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
64340L
CHARGING THE BATTERY PACK
Before using your Rechargeable Grease Gun for the first time, the battery pack should be charged for a
minimum of 1.5 hours. If the battery pack is already installed in the Rechargeable Grease Gun, remove it
by following the instructions under INSTALLING or REMOVING BATTERY PACK. As the battery pack
approaches the discharged state, you will notice a sharp drop in tool performance. When the tool is unable
to perform the task at hand, it is time to recharge the battery pack. Recharging the battery pack before this
condition is reached will reduce the total work life of the pack. Discharging the pack beyond this point can
damage the pack.
NOTE: Battery temperature will increase during and shortly after use. Batteries may not accept a full
charge if they are charged immediately after use. Allow the battery pack to cool to room temperature
before charging for best results.
Vent slots in top and bottom of charger must not be obstructed. Do not charge battery when
temperature is BELOW 0°C or ABOVE 40°C.
NORMAL CHARGING
Make sure the power circuit voltage is the same as that shown on the charger specification plate, then
connect to power source.
REMOVING THE BATTERY PACK
Depress the two battery release buttons (one button on each side of battery pack) and pull the battery
pack from the grease gun.
INSTALLING THE BATTERY PACK
Align battery pack with opening in handle, and push battery pack into handle until it locks into place.
SAFETY INSTRUCTIONS FOR CHARGER & BATTERY
SAVE THESE INSTRUCTIONS!! This section of the Manual contains important safety and operating
instructions for the charger.
•
Before using a battery charger, read all instructions and cautionary markings on the battery pack,
battery charger, battery and Rechargeable Grease Gun.
•
Do not expose charger to rain, snow or frost.
•
Do not pull on or otherwise abuse cord. Never pull charger by the cord when disconnecting
charger. Have damaged or worn power cord replaced immediately.
Do not attempt to repair the power cord.
•
Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected to
damage or stress.
•
Do not use an extension cord unless absolutely necessary. Use of improper extension cord could
result in a risk of fire and electric shock. If an extension cord must be used, make sure:
A: That the extension cord is properly wired and in good electrical condition.
B: Wire size of cord is at least as specified in the following chart:
Length of Cord in feet (m)
AWG Size of Cord (mm2)
C: If an extension cord is to be used outdoors, it must be marked with the suffix W-A following the
cord type designations. For example, SJTW-A to indicate it is acceptable for outdoor use.
• Do not operate charger with a damaged cord or plug. Have the cord replaced immediately to avoid a
hazard. Do not attempt to repair the power cord.
• Do not operate the charger if it has received a sharp blow, been dropped, or otherwise damaged in any
way. Take it to a qualified serviceman for repair.
• Do not disassemble the charger or the battery pack. Take it to a qualified serviceman when service or
repair is required. Incorrect reassembly may result in risk of
electrical shock or fire.
• Unplug charger from outlet before attempting any maintenance or cleaning to reduce risk of electrical
shock.
SW-Stahl und Werkzeugvertriebs GmbH
Leverkuser Strasse 65
D-42897 Remscheid
CHARGER OPERATION
CAUTION
25 (7.5)
18 (1)
Tel. +49 (0) 2191 / 46438-0
Fax +49 (0) 2191 / 46438-40
E-Mail: info@swstahl.de
50 (15)
100 (30)
18 (1)
18(1)
150 (45)
16 (1.5)
www.swstahl.de
Werbung
Inhaltsverzeichnis
