Phottix Mitros +TTL Transceiver Flash for Nikon Benutzerhandbuch Seite 10

Odin Tx (Transmitter Mode)
Using the Mitros+ in Odin Tx Mode allows for a flash to be used on camera in
TTL or Manual Mode as well as control three groups (A, B, C) – adjusting TTL and
manual power levels as well as flash head zoom on Mitros+ flashes set in Odin
Rx mode or other compatible flashes equipped with Phottix Odin receivers.
Using Odin Tx Mode
Odin Tx mode screen
After selecting Odin Tx Mode (see above)
1. Press the button to edit the groups.
2. The and
3. Pressing the button while a group is selected will change the mode
from TTL, M (manual) and Off.
4. Pressing the or
for adjustment to the EV Level ±3EV in 1/3 stop in TTL Mode or adjustments
to the power level (1/128 to 1/1 in 1/3 stops) in Manual Mode.
5. Press the button to exit the Odin Tx Mode editing menu.
Ratio Mode
Odin Tx Ratio mode screen
Ratio is similar to Nikon's native TTL system. The ratio of groups A and B can be
set from 8:1 to 1:8. EV levels can also be adjusted. Adjustments to the local flash
(L) mode and power can be made.
To access Ratio Mode:
1. Press and hold the
justment Menu will appear.
2. Press the button to open the editing mode.
3. Press the or
Ratio and Ratio EV adjustment.
4. Press the or
EV when selected.
5. The button will change the mode the local flash from TTL to Manual
to Off.
6. Press the button to exit Ratio Mode editing.
10
buttons will cycle though groups L, A, B, C.
buttons when a group is selected will allow
button while in the Odin Tx Menu. The Ratio Ad-
buttons to cycle though Local Flash(L) , Flash
buttons to adjust Local Flash EV, Ratio and Ratio
INSTRUCTION MANUAL
En
7. Press and hold button to exit Odin Tx Ratio mode and return to Odin
Tx Mixed Mode.
Please note:
The flash on camera (L) is not part of the ratio calculation. Power for the local
flash is controlled independently.
Adjusting Flash Head Zoom in Odin Tx Mode
1. Pressing the button will open the Zoom Adjustment Menu.
2. The and buttons will cycle though groups L, A, B, C.
3. The and buttons will adjust from Azoom (automatic zoom that
changes dynamically as a zoom lens is changed) and Mzoom 17, 18, 20, 24,
28, 35, 50, 70, 85 and 105mm.
4. Pressing the button will exit Zoom Adjustment Mode.
Adjusting Transmission Channels
1. From the Odin Tx or Ratio Menu, press the
Transmission Channel selection.
2. Press the and
3. Press the button to lock in the channel.
Odin Rx (Receiver) Mode
Odin Rx mode screen
When the Odin Rx Wireless mode is selected the Phottix Mitros+ Flash will
trigger using a built-in Odin-compatible receiver. While in Odin Rx Mode the
Mitros+ can be controlled and triggered from another Mitros+ Flash in Odin Tx
Mode or an Odin TCU.
Changing Channels and Groups
1. Press the button to access the Channel and Group selection.
2. Use the and buttons to select Channel or Group.
3. Use the and
or group assignment (A-C).
4. Press the button to exit Channel and Group editing mode.
5. Pressing the button will allow the EV adjustment for the flash to be set
using the and
Adjustment mode.
button to access the
buttons to cycle through Channels 1-4.
buttons to adjust the reception channel (1-4)
buttons. Press the button again to exit EV