Introduction; Layout; Scope Of Delivery; Intended Use - HERKULES HSE3500 Originalanleitung

GB

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
We hope your new tool brings you much enjoyment and
success.
NOTE:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by the
product that occurs due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service
technicians,
• Installation and replacement of non-original spare
parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due
to the non-compliance of the electric regulations and
VDE regulations 0100, DIN 57113 / VDE0113.
WE RECOMMEND:
Read through the complete text in the operating instruc-
tions before installing and commissioning the device.
The operating instructions are intended to help the user
to become familiar with the machine and take advan-
tage of its application possibilities in accordance with the
recommendations. The operating instructions contain
important information on how to operate the machine
safely, professionally and economically, how to avoid
danger, costly repairs, reduce downtimes and how to in-
crease reliability and service life of the machine.
In addition to the safety regulations in the operating in-
structions, you have to meet the applicable regulations
that apply for the operation of the machine in your coun-
try. Keep the operating instructions package with the ma-
chine at all times and store it in a plastic cover to protect
it from dirt and moisture. Read the instruction manual
each time before operating the machine and carefully
follow its information. The machine can only be operated
by persons who were instructed concerning the opera-
tion of the machine and who are informed about the as-
sociated dangers. The minimum age requirement must
be complied with.
16 І 96
2. Layout (Fig. A-M)
1. Tank indicator
2. Tank cover
3. 2 x 230 V~ socket-outlets
4. Earth connection
5. Overload cut-out
6. Voltmeter
7. Oil filler screw
8. Oil drainage screw
9. Oil deficiency protection for low oil switch-off
10. On/Off switch
11. Choke lever
12. Reversing starter
13. Petrol cock
14. Wheels
15. Axle
16. Foot
17. Push bar holder
18. Push bar
19. Screws size M8 x 40
20. Screws size M8 x 16
21. Washers for wheels
22. Securing split pins for wheels
23. Nuts M8
24. Spark plug wrench
25. Screwdrive

3. Scope of delivery

• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the pack-
aging and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport
damage.
• If possible, store the packaging until the warranty
period has expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

4. Intended use

The device is designed for applications operated with
a 230 V alternating current source.
Be sure to observe the restrictions in the safety inst-
ructions. The generator is intended to provide electric
power tools and light sources with electricity.
When using the device with household appliances,
please check their suitability in accordance with the
relevant manufacturer's instructions. In case of doubt,
ask an authorized dealer of the respective equipment.
The equipment is to be used only for its prescribed
purpose. Any other use is deemed to be a case of mi-
suse. The user/operator and not the manufacturer will
be liable for any damage or injuries of any kind caused
as a result of this.
Please note that our equipment has not been designed
for use in commercial, trade or industrial applications.
Our warranty will be voided if the equipment is used in
commercial, trade or industrial businesses or for equi-
valent purposes.