Intended Use; Package Contents; Safety Instructions - Conrad 1369184 Bedienungsanleitung

G
O P E R A T I N G I N S T R U C T I O N S
4-Channel Network
Video Surveillance Set
Item no. 1369184

Intended use

The digital recorder is used to record and monitor images from all four cameras supplied. The
device is operated via USB mouse and with an intuitive OSD menu.
The digital recorder is specially designed for the supplied cameras, which can be connected to
the digital recorder via a standard network cable.
The images are recorded onto a SATA hard drive (not included in the delivery, to be ordered
separately).
The safety instructions must be observed at all times!
Any use other than that described above could lead to damage to this product and involves
the risk of short circuits, fire, electric shock, etc. No part of the product may be modified or
converted!
This product complies with the applicable national and European requirements. All names of
companies and products are the trademarks of the respective owners. All rights reserved.
HDMI is a registered trademark of HDMI Licensing L.L.C.

Package Contents

• Digital recorder
• USB mouse
• Power adapter
• European type power cord
• 4x network cables
• 4x fixing screws for hard drive
• 4x cameras
• 4x mounting materials for cameras
• CD (including software and the original manufacturer's manual in English)
• Quick guide

Safety instructions

Damages due to failure to follow these operating instructions will void the
warranty! We do not assume any liability for any resulting damage!
We do not assume any liability for personal injuries and material damages
caused by the improper use or non-compliance with the safety instructions. In
such cases, the warranty will be null and void.
a) General
• The unauthorised conversion and/or modification of the product is not permitted
for safety and approval reasons (CE).
• If the digital recorder is used with other devices (e.g. a monitor and surveillance
cameras), the operating instructions and safety notices for these devices must be
followed.
• Any maintenance or repair work must be carried out by a technician.
• Do not leave packaging material carelessly lying around, as it could become a
dangerous plaything for children.
• In commercial institutions, the accident prevention regulations of the Employer's
Liability Insurance Association for Electrical Systems and Operating Facilities are
to be observed.
• If you have any questions that are not answered in this manual, please contact our
technical service or other specialist.
b) Power adapter
• The design of the power adapter/power cord complies with class II safety requi-
rements. Only use a standard mains socket as the voltage source for the power
adapter.
• The mains socket where the power cord is plugged in must be easily accessible.
• Use only the power adapter supplied to power the digital recorder.
• Do not pull the mains plug from the mains socket by pulling on the cable.
• If the power adapter or power cord is damaged, do not touch it; electric shock
carries a risk of danger to life!
First, switch off the mains voltage to the mains socket to which the power adapter/
power cord is connected (switch off at the corresponding circuit breaker or remove
the safety fuse and then switch off at the RCD protective switch, so that the socket
is fully disconnected from the mains voltage).
www.conrad.com
Version 07/15
Installation of a SATA hard drive
• First remove the casing lid of the digital recorder by unscrewing the retaining screws.
• An 8.89 cm/3.5" SATA hard drive is suitable for the installation. For use as surveillance de-
vice, you have to install a hard drive that can be used in continuous operation. These are
usually more expensive than "normal" hard drives.
Some manufacturers of hard drives offer hard drives that are specially designed for surveil-
lance systems.
Do not install conventional desktop hard drives in the digital recorder as these will age faster
or read/write errors may occur if the hard drives are used in continuous operation.
Furthermore, pay attention that the hard drive used does not develop an excess of heat.
• Attach the hard drive to the digital recorder by the recorder's mounting holes intended for this
purpose and 4 screws.
• Connect the power cord and the SATA cable between the hard drive and the digital recorder's
control board.
• Replace the casing lid of the digital recorder and fasten it with the screws removed earlier in
this step.
Mounting the cameras
• If you need to drill holes to secure the wall bracket, mark first the installation position on the
wall through the fastening holes in the wall bracket.
Also, if necessary, drill a hole in the wall that is large enough to pass the connection cable
through.
Make sure that you do not damage existing cables or lines when drilling.
Select the installation site so it is protected against attempts to tamper with the camera. For
this reason, the camera should be mounted at a minimum height of 2.5 m.
Then you can remove the mains plug from the mains socket. Dispose of the dama-
ged power adapter/power cord in an environmentally friendly way and discontinue
use. Replace it by a power adapter/power cord of the same design.
c) Operation
• This product is not a toy. Devices operated on mains voltage should not be used
by children. Particular care must therefore be exercised if children are around.
Use the product where it is out of the reach of children.
• The digital recorder, the power adapter and the power cord may not become damp
or wet; operation is only permitted in dry, closed rooms.
Never touch the power adapter and the power cord when your hands are damp or
wet. Danger of a life-threatening electric shock!
• The 4 cameras supplied are intended for installation and operation in indoor and
outdoor areas.
• The product must not be exposed to extreme temperatures, strong vibrations or
heavy mechanical stress. Protect it against dust and dirt.
• Never use the product immediately after it has been taken from a cold room into a
warm one. The condensation that forms can ruin the product under certain circum-
stances. The power adapter/power cord also have an associated risk for electric
shock!
Allow the product to reach room temperature before connecting it to the power
supply and putting it to use. This may potentially take several hours.
• Prevent the following adverse conditions at the location of installation and during
transport:
- Dust or flammable gases, fumes or solvents
- Strong vibrations, impacts or blows
- Strong magnetic fields such as those found in the vicinity of machinery or louds-
peakers
• Safe operation can no longer be assumed if:
- the device is visibly damaged
- the device no longer works
- the device has been stored under adverse conditions for a long time
- it was exposed to heavy loads during transport
• When setting up the product, make sure that the cables are neither kinked nor
pinched.
• Handle the product with care; it can be damaged by impacts, blows, or accidental
falls, even from a low height.
• Disconnect the power supply from the power socket if the product will not be used
for a while (e.g. storage).