Switching On/O; First Time Installation - Telefunken Xf32E419D Bedienungsanleitung


To Switch the TV On
Connect the power cord to a power source such as a
wall socket (220-240V AC, 50 Hz).
To switch on the TV from standby mode either:
Standby
• Press the
numeric button on the remote control.
• Press the the middle of side function switch on the
TV in.

Standby
Press the button on the remote control or
press the middle of the side function switch on the
TV in and hold it down for a few seconds, the TV will
switch into standby mode.
To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched into standby mode, the standby
LED can blink to indicate that features such as Standby
Search, Over Air Download or Timer is active. The LED can
also blink when you switch on the TV from standby mode.

First Time Installation

When turned on for the first time, the language
selection screen is displayed. Select the desired
OK
language and press
On the next screen, set your preferences using the
directional buttons.
Note: Depending on the
to set and conrm a PIN at this point. The selected PIN cannot
be 0000. You have to enter it if you are asked to enter a PIN
for any menu operation later.
About Selecting Broadcast Type
Digital Aerial: Digital Aerial
If
option is turned on, the TV will search for digital
terrestrial broadcasts after other initial settings are
completed.
Digital Cable: Digital Cable
If
option is turned on, the TV will search for digital cable
broadcasts after other initial settings are completed.
      
message may be displayed before starting to search.
Select YES and press OK to proceed. To cancel
NO
operation, select
Network
or set values such as
ID and Search Step.OK button.
Note: Searching duration will change depending on the
Search Step
selected .
Satellite: If Satellite broadcast search option is turned
on, the TV will search for digital satellite broadcasts
after other initial settings are completed. Before
satellite search is performed some settings should be
made. Antenna Type
can select Antenna Type
Cable or DiSEqC switch
Programme +/-
button,
.
Country selection you may be asked
broadcast search
broadcast search
OK.
and press You can select
Frequency Network
,
as Direct, Single Satellite
by using "
" or " " buttons.
• Direct: If you have a single receiver and a direct
satellite dish, select this antenna type. Press
 Select an available satellite on the next
screen and press
• Single Satellite Cable: If you have multiple
receivers and a single satellite cable system, select
this antenna type. Press OK
or a
settings by following instructions on the next screen.
OK
Press
• DiSEqC switch: If you have multiple satellite dishes
DiSEqC switch
and a
Press OK   You can set four DiSEqC
options (if available) on the next screen. Press OK

Analogue: If Analogue broadcast search option is
turned on, the TV will search for analogue broadcasts
after other initial settings are completed.
Additionally you can set a broadcast type as your
favourite one. Priority will be given to the selected
broadcast type during the search process and the
channels of it will be listed on the top of the Channel
List 
You can activate

environment and depending on the TV model being
used, the supported features of it may be displayed
on the top of the screen as an info banner. This option
is intended only for store use. It is recommended to
select Home Mode for home use. This option will be
System>Settings>More
available in

Depending on the model of your TV and the country
selection Privacy Settings menu may appear at
this point. Using this menu you can set your privacy
privileges. Highlight a feature and use Left and Right
directional buttons to enable or disable. Read the
related explanations displayed on the screen for
each highlighted feature before making any changes.
You can use
and down to read the entire text. You will be able to
change your preferences at any time later from the
Settings>Privacy Settings menu. If the Internet
Connection
Settings screen will be skipped and not displayed.
If you have any questions, complaints or comments
regarding this privacy policy or its enforcement, please
contact by email at smarttvsecurity@vosshub.com.
Press OK button on the remote control to continue and
the Network/Internet Settings menu will be displayed,

whether you want to do the network settings. Please
refer to 

Wake
On 
completed press OK. To skip to the
English - 48 -
OK
to scan for services.
to scan for services.
, select this antenna type.
OK
to continue.
Store Mode option at this point.
Programme +/- buttons to scroll up
option is disabled
 
OK to
menu and can
Network/Internet