Beamz 150.487 Gebrauchsanleitung Seite 4

Foot switch mode：You can connect the footswitch unit (in any working mode) after entering footswitch mode.
Footswitch "BLACKOUT": Press the "BLACKOUT" pedal to turn off all LEDs in parbar lights and the LED Display will
show OFF. Press "BLACKOUT" again to return to the last scene before turn off all LEDs.
Footswitch "HOLD": Press the "HOLD" pedal to hold the data and display. The LED display will show "HoLd" . Press
"HOLD" pedal again to return to the last scene before hold.
Footswitch "SOUNDON": Press the "SOUNDON" pedal to enter sound mode and to select four different sound types. You
can also press the "MENU" button and use the "Up" button to select the four different sound types using the main controller
when the parbar is working in Foot switch mode .The LED display on parbar will show "Soun".
Press "SOUNDON" pedal to enter sound mode and to choose from four different sound modes. You can also select the four
different sound kinds by pressing the" MENU" button and using the" UP"
On the main controller press the "MENU" button and use the "Up" button to select the "SOUNDON" button on the foot
controller to choose different patterns. The LED display on parbar will show "Soun".
Footswitch "PRESET": Press "PRESET" pedal to system reset. The LED display on parbar will show "APon" Now use the
controller on the parbar, press "Menu" and "Up" to enter AUTO mode, "Color" choosing mode and SOUND mode. You can
use "PRESET" of the footswitch to select RGB->R->G->B->RG->GB->RB->RGB-> AP01-> AP02-> AP03-> AP04->
AP05-> AP06-> AP07-> AP08-> AP09-> AP10-> AP11-> AP12-> ALL (run all AP01-AP12 patterns one by one).
PLEASE NOTE - During operation, if there is no press on the button or controller button within 5 seconds, the Blue LED
display will turn off but will still display a small dot on the bottom right hand corner. If you press again, it will show the last
item displayed on the display. When the LED parbar is connected to the DMX 512 controller or another LED parbar, the Blue
LED DMX indicator flashes. When you connect two LED parbars as master/slave, the first Blue dot on display flashes.
The Flashing blue LED indicates that a DMX signal is present or you are connected to another Parbar.
DMX channel data
PLEASE NOTE - the DMX function will only work if CH1 is set to DMX Mode, which is set by adjusting the DMX fader
value below 009 and the DMX Fade function (CH2) is set to light output level above 0% or DMX fader value greater than 1.
Please Locate CH1 position the fader greater than 000 and less than 009 DMX fader value. Locate CH2 fader and check fade
function control is set. Increase to DMX fader value 255 for 100% full on output. Then you will have control of the DMX
functions.
Channel Function
Mode 01
Mode 02
Mode 03
Mode 04
Mode 05
Mode 06
Mode 07
CH1
Mode 08
Mode 09
Mode 10
Mode 11
Mode 12
Mode 13
Mode 14
DMX value Function
000～009
ENABLES USE OF DMX CHANNELS 1-15
010 – 029
Run program 01 、CH3>15
030 – 049
Run program 02 、CH3>15
050 – 069
Run program 03 、CH3>15
070 – 089
Run program 04 、CH3>15
090 – 109
Run program 05 、CH3>15
110 – 129
Run program 06 、CH3>15
130 – 149
Run program 07 、CH3>15
150 – 169
Run program 08 、CH3>15
170 – 189
Run program 09 、CH3>15
190 – 209
Run program 10 、CH3>15
210 – 229
Run program 11 、CH3>15
230 – 249
Run program 12 、CH3>15
250 – 255 4 Sound patterns
button to choose the sound kind.
4