Description Of Device / Spare Parts; Assembly; Preparing For Startup - ATIKA BS 205-2 Originalbetriebsanleitung

Repairs to other parts of the machine must be carried out
by the manufacturer or one of his customer service points.
Use only original spare parts, accessories and special
accessory parts. Accidents can arise for the user through
the use of other spare parts. The manufacturer is not
liable for any damage or injury resulting from such action.

Description of device / spare parts

►
Pos Order-no Designation
1 Adjusting wheel for clamping of saw band
2 Upper case door
3 ON/OFF switch
4 Lower case door
5 Lower band saw roll
6 Saw table
7 366361 Stopper guidance profile
8 366358 Parallel stopper
9 366359 Table insert
10 366368 Saw band
11 Saw band coping
12 Adjusting wheel for saw band coping
13 Upper band saw roll
14 Transverse adjustment saw table
15 366372 Label for angle scale
16 Splinters suction socket
17 Base
18 Motor
19 Line cord
20 Adjusting wheel for upper band saw roll
21 366370 Push stick
22 Pushing stick holder
23 Cover ►
24 366355 Rubber pulley for Band saw roll ►

Assembly

Assemble saw table
1. On the underside of the saw table (6), unscrew the two
star knob nuts (A) and the nut (B) and pull off the stopper
guidance profile (7).
2. Insert the table insert (9).
3. Guide saw table over the saw band and put it on the
saw table guidance.
4. Mount the saw bench with four screws (M6) and
washers (Ø 6.4) to the saw bench guide. Do not tighten the
screws; the saw bench still needs to be moved slightly!
5. Push the saw bench in the direction of the arrow and tighten
the screws
6. Slide the stopper guidance profile (7) under the saw
table and tighten the star knob nuts (A) and the nut (B).
.
►
18
Angle the saw table rectangularly
1. Place the saw band coping completely upwards (see
„Adjustment of the saw band coping" p. 19)
2. Check saw band tension (see „Saw band tension" p. 19)
3. Loosen the fixing screws (C /D).
4. Angle the saw table with the help of an angle
rectangular to the saw band.
Unscrew the lock nut (E)

 Turn the adjusting screw (F) until the saw table is at a
right angle to the saw band.
 Retighten the lock nut.
 Retighten the fixing screws (C / D).

Re-check the perpendicularity using a try-square
5. If after adjusting the rectangularity the arrow (G) does no
longer show to 0°
 remove the label for the angle scale (23) and re-align it.
Push stick
Hang the push stick (21) on the push stick holder (22).

Preparing for startup

 To obtain a perfect working of the machine follow the
following advices:
 Place the saw in a place that fulfils the following conditions:
 secured against slipping
 free of vibrations
 even
 free of tripping hazards
 adequate light
For a safe standing position the saw must be tightened

on a stable ground (i.e. work bench or underframe) on
optimal working height:
Provide ground with 4 bore holes
 Before each use, check
 Connection cables for defects (cracks, cuts, etc.)
Do not use any defective cables.
 the table insert for its proper condition
 the saw band for its faultless condition
 that all doors are closed
 whether the pushstick is to hand
 Do not use any deformed or damaged saw bands.
 Replace a worn-out or damaged table insert immediately.
 When the machine is not used open-air it must be
connected on both suction sockets with a splinter extraction
system (i.e. portable small dust extractor).