Exibel H28S Kurzanleitung

Bluetooth Headset
Art.no 38-5589 Model H28S
Please read theentire instruction manual before using theproduct and then save
it for future reference. Wereserve theright for any errors in text or images and any
necessary changes made to technical data. Ifyou have any questions regarding
technical problems please contact our Customer Services.
Safety
• Check your local regulations regarding mobile phone use in combination
withdriving.
• Shut off both theheadset and mobile phone in areas where you are requested
to do so, such as hospitals, aircraft or explosive environments.
• Use only theincluded USB lead to charge theheadset.
• Do not let children play with theheadset.
Things to consider:
• Other wireless equipment using thesame frequency can reduce
thetransmission range.
• The range of all wireless equipment depends on thetype of obstacles located
between thetransmitter and thereceiver (e.g. aconcrete wall will interfere with
thesignal more than aplasterboard wall).
If you experience problems, try thefollowing:
• Turn off any other existing wireless equipment to check if this is thecause of
theproblem.
• Move any other existing wireless equipment. Shorten thedistance between
thesending and receiving devices and reduce thenumber of obstacles (walls,
furniture, etc.) between them.
Buttons and functions
1. [ ] Multifunction button
2. LED indicator
GREAT BRITAIN - CUSTOMER SERVICE
contact number: 08545 300 9799 e-mail: customerservice@clasohlson.co.uk internet: www.clasohlson.com/uk
English
Charging
Note: Theheadset cannot make or receive calls while it is being recharged.
1. Connect theincluded USB cable to theheadset and to asuitable USB
charger (e.g.computer or other mains charger).
2. The LED indicator shines red when charging is in progress.
3. Charging takes 1–2 hours, and when thebattery is fully charged theLED
indicator will shineblue.
4. If theLED indicator changes from blue to red during use, it means that
thebattery needs charging.
Operating instructions
Turning the headset on
Hold down [ ] for 3 seconds. Theheadset will beep, theLED indicator
will flash blue and theheadset will come on. TheLED indicator will flash quickly
2times every 4th second when theheadset ison.
Turning the headset off
Hold down [ ] for 5 seconds. Theheadset will beep, theLED indicator will
flash red and theheadset will switch off.
Connecting the headset to a mobile phone via Bluetooth (Pairing)
1. Check that theheadset is switched off.
2. Hold down [ ] for 5 seconds until theLED indicator flashes red/blue.
3. Activate Bluetooth on themobile phone that is to be paired with theheadset
and set it in search mode.
4. The Bluetooth speaker will appear as "H28S" on your mobile phone.
Selectthis as thedevice to be connected. Referto your mobile phone's
instruction manual if you are unsure.
Note: Ifyou are prompted to enter aPIN code on your mobile phone, you
should enter (four noughts). Certain mobile phones may even require
0000
you to approve theconnection.
5. The LED indicator will flash quickly once every 4th second when theheadset
and mobile phone are paired.
6. The next time theheadset is switched on it will automatically connect to
themobile phone.
Connecting the headset to a second mobile phone via Bluetooth
The headset can be connected to 2 mobile phones at thesame time. Procedure:
1 1. Connect thefirst mobile phone to theheadset as described above.
2. Connect thesecond mobile phone in thesame way as thefirstone.
3. Turn theheadset off.
4. Switch theheadset on again but only hold down the[
3 seconds so that theheadset comes on as normal without being in
theBluetooth mode.
Accepting an incoming call
2
• The headset emits anaudible signal if anincoming call is received, press
[ ] once to answer thecall.
• You can also answer thecall by pressing thecorresponding button on your
mobile phone.
Ending a call
• Press [ ] once to end acall.
• You can also end thecall by pressing thecorresponding button on your
mobile phone.
Transferring calls from the headset to a mobile phone
• Hold down [ ] for 2 seconds to transfer acall from theheadset to
amobile phone.
• Hold down [ ] for 2 seconds again to transfer thecall back to theheadset.
Redialling the last number called
Press [ ] twice in quick succession to redial thelast number called.
Rejecting calls
When an incoming call has been received, hold down [
reject the call.
Voice dialling
Hold down [ ] for 3 seconds, say thename of theperson you wish tocall.
Note: Thefunction only works if your mobile phone supports voice dialling.
Care and maintenance
• Avoid exposing theheadset to moisture, damp, high temperatures and humidity.
• Clean theheadset using alightly moistened cloth. Onlyuse mild cleaning
agents, never solvents or corrosive chemicals.
Troubleshooting guide
The LED indicator shines red
The headset needs charging. Connect theheadset to acomputer or other USB
charger. Referto the
Charging
The headset cannot connect to the mobile phone
• Make sure that both theheadset and thephone are fully charged and try to
connect again later. Referto theConnecting theheadset to amobile phone
via Bluetooth paragraph above.
• Make sure that thedistance between units is no more than 10 metres and
that there are no electrical or other devices that might cause interference
between them.
• If none of theabove solutions help, refer to themobile phone's operating
instructions.
] button for
Disposal
This product should be disposed of in accordance with local regulations.
Ifyouare unsure how to proceed, contact your local authority.
Specifications
10m
Range
3.0
Bluetooth
7hours
Talk time
100hours
Standby time
8.5g
Weight
] for 2 seconds to
paragraph above.