Viltrox DC-X2 Produktanleitung

English
VILTROX
DC-X2
6-inch Professional Photographic Monitor
nurmx
Please readtheUserManualcarefullybeforeusingthis product.
Please keepthis Manual p roperlyforfuturereference.
Please useit correctlyafterfullyunderstanding the contentsherein.
ShenzhenJueyingTechnologyCo.,Ltd. Executive standard: Q/JYKJ001-2019
Tel: +86-755-2877 9024
Fax: 0755-2877 4730
Email: info@viltrox.com Website: 'vwwv'.viltrox.com
Address:1207,Floor12,BlockB,Chinto Science&Technology Building, MinzhiStreet,
Longhua,Shenzhen,Guangdong,China
Production Address:Floor3, Building 1,SimaiouSciencePark,NO.52-1,Juyuan Road,
QiuchangTown,HuiyangDistrict, Huizhou,Guangdong,China
Cleaning
I. Pleaseremove the battery before cleaning.
2.The surfaceofthe LCDscreen hasbeen speciallytreated to reduce
reflected light, so its performance may be reduced in caseof improper
maintenance.
3. Gentlywipe the screen or chassiswith a soft and dry cloth (such asa
cleaning cloth or glass cleaning cloth).
4. Removestubborn stains usingneutral detergent.
5. Do not clean this device using thinner, alcohol and other organic solvents
to avoid damage to the chassisand screen.
6. Do not wipe the chassiswith a rough cloth to avoid scratching the surface
of the chassis.
7.The surfacecoating of the chassismay be damaged or peeled off after it
has been in contact with rubber orvinyl products for a long time.
Introduction to functions
TheDC-X2 i sa6-inchprofessional photographic monitor with a resolutionof
1920x 1080 pixels.It'ssuitable for digital cameraswith interchangeable
lensesor digital HDcamcorders, providing real-time display of high-definition
signalsfrom HDMIsources.This powerful monitor offers a monitoring
assistancesystem for photographers and meetstheir high-definition image
quality needsin photography.
Product features:
0 3D LUTfunction: With the 3D LUT,it's possible to control the full
three-dimensional color space,significantly expanding the monitor's color
displaypotential.Thisfeaturealsoserves asa solidbackbonefor achieving
hardware calibration's 'what you seeiswhat you get' capability. The device
can load up to 20 3D LUTfiles via a USBinterface.
O Audiocolumn:Monitorsthe audiosignalswithinthe HDMI h igh-definition
signals,performing real-time waveform switching to reflect different highs and
lows.
O Gyroscopefunctions: This device hasgyroscope detection function to
adjustthe screen up anddown andautomatically flip the imagewithout
manual adjustment, optimize and improve the userexperience,and thus
better meet the needsof photographers.
O Brightness histogram: M onitorsthe brightness ofimagestransmittedby
HDMI high-definition signals,capturing and displaying real-time changesin
brightness valuesaccording to imagevariations.
O Falsecolorfunction: It can achieve more precise exposure and lighting
controlthroughimageconversion, w ith redfor excessive lighting,bluefor
insufficient lighting and green for appropriate lighting conditions.
O Focusing function:Setthefocusonthe screenarea.
O De-squeeze function: Restoresthe compressed and deformed image ofthe
camera,displaying the originalproportionofthe physical o bject.
O Powersupply. It can switch amongthe three power supply modes of DC
adapter, lithium battery and Type-Cat anytime to fully meet the power supply
needsof customers in different scenarioswithout waiting for a single power
supply.
O Shortcutkeys: A llowssettingdifferentshortcutkeysaccording to customer
preferencesfor one-touch settings without the need to enter menu
configurations.
O Signal:This device hasHDMI INfunction; in addition, it comes with HDMI
OUToutput function, which is convenient to connect other monitors or
deviceson site and thus meet the external expansion display functions of
different photographers.
O USBinterface: S upportsUSBinterfacefor upgrades and loading3DLUT
function files.
O Touchscreen: 6 -inchsensitive touchscreenisprovidedto facilitate
different photographers to operate the device.
3
Installationof batteryand adapter
Installation of battery
This product can be equipped with rechargeablelithium batteries.
The battery models include NP-F550/F570/F750/F770/F960/F970 and other
specifications.
2.To remove the battery, press
1. 1 to
and hold the battery release
the right (without releasing).A
button while slidin the
battery tothe left, {en
clicking sound indicates that the
battery is securelyin place.
remove it.
A Note:Be carefulto preventthebattery
from fallingon thegroundwhen
takingit Out.
Installation of adapter
1. Select the direction in which the
adapter is mounted accordingto the
shapeof hot shoe on the camera. (O))
2.Alignthe 1/4 screwof the adapter with
the 1/4 screw hole on the device.(@)
(2)
3.Tighten the adjustment knob of the
adapter.(O)
4. Usethe adapter
@Fullyinsertthe baseofthe adapterinto the universal h ot shoebasein
the direction shown in the figure.
@Tighten t herotary table oftheadapter t ofixit onthecamera.
A Note:Beforeusingacamera with a pop-upbuilt-inflash,you needto notethefollowing
points:TurnOffthebuilt-inflashOfcamera.Ifthe cameraisdesigned with abuilt-in
autoflashfunction,please turn off thisfunction.
Please remove this devicefrom thecamerabeforeusingtheflash.
5
Touch screen operation
Menu: Double-tap the screenstart the menu options; tap the blank spaceto exit
the menu mode.
Volume adjustment: Backlight adjustment:
Scroll up and down on the left side Scroll up and down on the right
of the screenfor adjustment. sideof the screenfor adjustment.
Zoom in and out: Zoom in and out with your finger (asshown in the figure) to
see details.
(Zoom in) (Frame disappears) (Double-tap again)
Note:DO notdouble-tapto displaythemenuintheprocess of zoominginandout, but
double-tapto displaythe menuafterthe "boxforzoomingin andout" disappears.
Menu function
Power On/Off
[ Power On]
Longpressthe PowerButton for 3 secondsandthen release;
the indicator light will turn green,and thescreenwill light up.
(Whenthereis asignal,the indicator lightturns green;whenthere
isno signal,the red light turns on.)
Warning!
[Power Off]
Confirm shutdown?
Longpressthe PowerButton (6), the screenwill displayan
'operationreminder';select 'confirm',and theindicator light and
Cancel
screen will turn off.
Introduction to menu
USB Input Source
(Wave form)
[Monitoringtool]
[Markand composition]
[Image)
(Systemsettings)
V«tmpe
7
Troubleshooting
Necessaryinspections should be carned out beforesending the device for
repair. Pleasecontact your dealer ifthe device isstill unable to work properly.
Fault Causes andtroubleshootingmeasures
The battery isnot unlocked —+ pressthe battery releasebutton, and then
Battery cannotbetakenOut
takeout the
Thebatteryhasrundown replace thebattery.
Thisdevicehasnopower The power adapter (not accompa nied) isdisconnected. Pleasereconnect it
property.
This device cannot be
ncorrect type of adapter used,p easeselectthe correct adapter.
mounted in camera
Thecamera isin power saving mode and some camera operations cannot
be performed. Pleasepressthe shutter button ha Ifr.'ayto exit the power
savingmode. TheHDMI h ighdefinitionsignalcableisdisconnected; orthe
NOimages aredisplayed
signalsource isnot turned on. Pleasereconnect and set up correctly.When
on the screen ofthis device
usingacamerawithoutaliveView function,the captured images cannotbe
displayed onthisdevice. P lease refer t o the instruction manual o f camera
fordetails.
Thisdepends onthe camera. WhenanHDMI h igh-definition signal c ableis
No images are displayed
connected to this device, imagesmayonlydisplayed onthe screen ofthis
on the screen of camera
dejice.
Please ensure thatthe volumeof thisdevice is notsetto Obeforeconnecting
No sound can be heart
headphones. Makesure that the sound setting of camera is not setto OFF.
This depends onthe camera. Whenit isconnected to thisdevice, i t may
No photo can be captured
someti m esswitchto playbackmode.
Please switchthecamerato capturemodebeforetakingphotos.
Thescreen isnotclearoutdoorsBlock out thesunwith a hood.Tumthe backlight v alueofthisdeviceup.
Available signal format
This device supports the following signal formats:
Number
Number
Frame
System Scanning Aspect ratio
of effective
frequency
of buses
lines
575 / 501 (PAL)
16:9 /
625 575 50 2: 1 interlacing
480 / 601( NTSC) 16:9 /
525 483 60 2:1 interlacing
576 / 50P 625 576 50 Sequential s canning 16:9 /
480 / 60P 16:9 /
525 483 60 Sequential scanning
640 X480 /60P
525 480 60 Sequential scanning
1080 / 501
1125 1080 50 2: 1 interlacing 16 19
1080 1601 1125 1080 60 interlacing 16
720 / 50P
750 720 50 Sequential s canning 16
720 /60P
750 720 60 Sequential scanning 16
1080 /50P
1125 1080 50 Sequential scanning 16 19
3840X2160/30P
2250 2160 30 Sequential scanning 16
Design or specifications are subject to change without notice.
9
Contents
User Manual
Operation
Introduction to functions.
Part
Installation of battery and
Connection Method for High-definition Signal Cable...................
Sunshade hood
Touch screen
Menu function...................................................................................
Troubleshooting...........................................
Available signal
Prod uct specifi cations..... • • •
Firmware
Operation precautions
Pleaseread this UserManual and the operation instructions of camera
carefully.
1. Pleaseusea compatible battery or power adapter.
2. Donot placeany heavyobjects on the screen to prevent loss of screen
uniformity.
3. Donot placethis device near liquids, becauseit is not designedwith
waterproof, splash-proof and dust-proof functions.
4. Do not place this device in the sun for a long time, or make itcloseto a place
with high temperature for a long time, so as not to cause deformation or
malfunction of machine.
5. Donot placethe device in a placewith excessivevibration, so asto protect it
from being damage afterfalling from a high place.
6. Donot placethe device in a placewith excessiveelectromagnetic strength
to avoid malfunction.
7. Donot placethe device in a sandy place,so asto avoid malfunction caused
after being attacked by sand and dust.
8. Donot dispose of this device with general waste.
9.The top, ventilation holes and metal parts ofthis device may become hot
after it hasbeen usedfor a long time. Pleaseuseit with care.
10. Ifthe device is used in cold environments, horizontal lines or residual
images may appear on the screen.This is not a malfunction. The screenwill
return to normal once the monitorwarms up.
11.Pleasefollow the regulations about the operation of this device on the
airplane in the take-off and landing processof airplane.
Parts identification
(j)
t)
@ @ 139
(j)Back/Menu Button 01/4 Screw Hole
@)ShortcutKey @CooIingAir Intake
@DispIay Screen Port
@Fan Exhaust Vent @Type-C Port
(5)IndicatorLight @9Cooling Air Intake
@Power Button 091/4 Screw Hole
Input @Cooling Air Intake
@HDMIOutput O@USBInterface
@HeadphoneJack @Battery ReleaseButton
@CooIingAir Intake @Battery Slot
ConnectionMethodfor High-definitionSignalCable
Connection of HDMIHigh-definition Signal Cable
I.Connect the device to the camera using the accompanied HDMI
(Pleasepurchase extra HDMIcables ifthe HDMIhigh-definition signal cable is not long
enough.)
2.The image of camera viewfinder will be displayed on the screen of the
device after turning on the power switch of the camera and the device.
Please set it to AUTO or 16:9 if the camera is designed with an HDMI output
setting function.
(Note) Whenconnectingthe devicetothe cameraviaan HDMIhigh-definitionsignal
cable,dependingon the camera,thefollowing mayoccur:
Theimage mayonly be displayedon thedevice'sscreen, w ith no imageshown on the
camera's screen.
(Tipl Inthefollowing situation, a ftera certain period, t hescreen willdisplay a 'nosignal'
message:
The camerais notoutputting asignal.
HDMIhigh-definitionsignalcableisdisconnected.
Sunshade hood
1. Put the device on the two bottom 2. To remove the sunshade,
brackets of the hood, and then pull the two top supports
gently buckle it up to complete the outward.
installation of hood.
Pleaseopen and close the hood in the steps below:
Pressthe button, and the sunshade
will open automatically.
(Wave form)
VolumeBar on/0ff
Histogram YHistogram(On/Off)
Vectorscope on/0ff
RGB Parade RGB
Fullwaveform On/Off
3D LUT open Luttable list
(Monitoringtool]
Red (0-10) Green (0-10)
Mode 1
00+1000/0
Gray
On/Off
Underscan
on/0ff
On/Off
On/Off
[Markand composition)
Marker Color (White/Black/Red/Green/Blue)
Marker Trans(0FF/Low/Medium/High)
85% 90%
Centra
2.35:1
Auto 4B 149 16:10 16:9
1AX 2X
1.3X 1.33X 1.5X
[Image)
Brightness vo-1000/0
Contrast 096-1000/0
0K
Saturation wc-1000/0
Hue 0+1000/0
Sharpness 096-1000/0
Backlight vo-1000/0
Color Temp
Power
5600K 6500K
RGB Red(O-255) Green(0-255)
[Systemsettings)
Language Language CH
FanSpeed Auto OFF Low
Volume wc-1000/0
OSD Menu OSDtrans(0FF/l-ow/Medium/High)
FKey
Fl F2
30
System Reset Product
Product specifications
DisplayScreen 6-lnch IPS Touch Screen
Resolution
Aspect Ratio 16:9
Contrast
1000:1
Refresh Rate
60Hz
ScreenBrightness 2000cd/m2
ViewingAngle
PixelDensity 360PPI
Color Gamut
ColorDepth
8Bit
Input Interface
HDMI IN
Output Interface HDMI OUT
CoolingFan
Yes
Weight z 324.5g(Monitor)
Dimensions
USB Interface SupportOfUSBupgradeand3DLutfile input
Audio Output HeadphoneJackQ3.5mm
Power nterface DC12-18V/2A,Type-C>9V/3A
ApplicableBattery Lithium BatteryNP-F550/F570/F750/F770/F960/F970
WorkingTemperature
ooc-650c
StorageTemperature ooc-750C
Firmware update
1. Download the latest firmware from www.viltrox.com.
2. Extract and store the latest firmware in a removable
3. Turn on the monitor and insert the USB drive
interface.
) -+ System -+ Firmware Update
4. Go to the menu: System Settings (
o
—+ Click 'Confirm', then automatically switch to the update interface.
5. Wait for the progress bar to complete loading. After loading, the
system will shut down automatically.
6. Press the power button to restart, wait for the progress bar on the
interface to complete, then the logo appears, indicating the firmware
update is complete.
Note: Pleaseuse a FAT32formatted USBdrive for upgrading.
VILTROX
2
3
3
.
— .5
DC-X2
.6
6
.9
• • •
. 10
„ 10
:+86-755-2877 9024
2
1.
I)) fiÉ
DC-X2E
0 3D LUTIjJfiä: CUT,
*iQåöJiMi-t
o a-fifr:
O t-ki-&:
0 18%:
4 3
4.
6
5
RGBHistogram(On/Off)
YUV
In Use...
Blue (0-10)
Mode 2
Blue
Green
Overscan
Flip-v
MarkerThick (1-3)
93% 96%
Trisection
1.85:1 9:16
1.85:1 23511 Full
IOX
1.6X 1.8X 2.ox
USB
7200K 9300K
Blue(O-255)
Language EN
Medium High
OSDtime (OFF/5snos/15S)
Manual Update
8 7
Éihfim;«,
USB drive.
into the monitor's USB
575/ 50KPAL)
625
480 / 601( NTSC) 525
576 / 50P
625
480 / 60P
525
640X480 /60P
525
1080/501
1125
1080/601
1125
720/50P
750
720/60P
750
1080/50P
1125
3840X2160/30P 2250
10 9
SYN....
wurzx
o
1.
BifibSE:Q/JYKJ001-2019
8.
A:0755-2877 4730
liiJil±: www.viltrox.com
10.
11.
LUTI#O
INIjfiÉ; %ääHDMl OUT $fiH:å1jfiÉ,
BB<j,
O
(O)
"6#iÅ"
Efiik
Parade SOLUT
F-fLöHE
575 50
483 60 16:9/
576 50 16:9/
60
483
480 60
1080 50 16:9
1080 60 16:9
720 50 16:9
720 60 16:9
1080 50 16:9
2160 30 iZfiE*ä 16•.9
2
.3
4
5
6
6
7
.9
10
10
2
(j) (4)
0)
01/4N47L
@DCEQ
5fiÄ
@HDMI
4
lÉ]5Mü,
6
Parade
RGB YUV
3DLUT5Æ
3D LUT
"(0-10)
*Et2
0+1000/0
85% 93%
235:1 1.85:1 9:16
14:9 16:10 16:9 185:1 2.35:1
1.4X 4X lox
1.3X 133X 1.6X 1.8X 2.ox
00+1000/0
00/6-1000/0
00+10096
00+10096
5600K 6500K 7200K 9300K
RGB
0+1000/0
OSDæ
Fl
8
1920 x 1080
16: 9
1000: 1
60Hz
2000cd/rr6
1600
360PPI
1000/0±30/0sRGB/Rec.709
8Bit
HDMI IN
HDMI OUT
DC12-18V/2A, Type-c >9V/3A
ooc-650C
ooc-750C
10