Inhaltsverzeichnis
Werbung
Operating Instructions
Note: This chapter contains excerpts from the operating instructions. For further particulars please refer to the appropriate user instructions the part number of which is indicated in the relevant spare
parts list.
REMOTE
OPEN/CLOSE
GB
SURROUND
SENSOR
POWER 6
SOUND
FUNCTION
UBS
VOLUME
OPEN/
CLOSE
p
CD Control
CD Display
Cassette Control
(the illustration shows: RR 650 CD)
Top and front panel
VOLUME
– to adjust the volume
UBS
– to switch the U
B
S
on and off
LTRA
ASS
YSTEM
FUNCTION
– CD:
to switch to CD mode / Power On
– TAPE/OFF: to switch to TAPE mode / Power Off
– RADIO:
to switch to RADIO mode / Power On
SURROUND SOUND
– to switch the surround sound effect on and off (only RR 650 CD)
REMOTE SENSOR
– to receive the remote signals (only RR 650 CD)
OPEN/CLOSE
– to open the CD door
POWER
6
– lights up when the unit is on
BAND
– to select between FM, MW, and LW waveband
SCALE
– tuning dial scale
FM STEREO
6
– lights up when receiving FM stereo stations
TUNING
– to tune to a radio station
MIC
– microphone under the speaker grill
p
– connection for headphones
CONTROLS
SOUND CONTROL
Remote control (only RR 650 CD)
Volume
Changing the batteries
• Adjust the volume to the desired level with the
VOLUME control.
If the range of your infrared
remote control seems to
decrease, or if certain individual
PLAY
UBS (Ultra Bass System)
functions can no longer be
STOP
carried out, you should replace
• Press UBS to enhance the bass response:
PREV.
NEXT
the batteries.
w
UBS OFF
x
UBS ON
VOLUME
Two mignon 1.5 Volt LR03 size
AAA are required.
To change the batteries, open
Surround Sound (only RR 650 CD)
the compartment on the back of
the remote control. Ensure that
This feature creates an additional 3-D effect from
the batteries are inserted properly
stereo sound which is relayed by the speakers.
(note the markings in the
• Press SURROUND SOUND to switch this effect
compartment).
on and off
And in the interest of the
w
SURROUND SOUND OFF
environment: Remember that
x
SURROUND SOUND ON
batteries must always be
disposed of properly.
Note:
The sound controls can be used with radio,
PLAY 2
– to start and interrupt CD playback
CD or cassette playback.
STOP 9
– to stop CD playback
However, they have no effect on cassette
PREV. ¡
– to skip and search backward
recording.
NEXT ™
– to skip and search forward
– VOLUME + – to adjust the volume
Back panel
FM MONO
/
STEREO / BEAT CUT:
Stereo headphone socket p
– When BAND switch is in FM:
to select between FM STEREO and FM MONO
• You may connect stereo headphones having a
– When BAND switch is in MW/LW:
3.5 mm plug to the jack
for eliminating possible whistle tones during
– Inserting the plug will disconnect the speakers.
MW/LW recordings
AC MAINS: Socket for mains lead.
CONTROLS
BAND
CD Control
SCALE
SKIP/SEARCH
FM STEREO 6
STEREO
FM
MW
∞/5 6/§
– to skip and search
LW
FM
TUNING
backward/forward
TUNING
REPEAT
– to repeat one/all tracks
PROG.
– to programme track numbers
in the memory
PLAY/PAUSE 2; – to start and interrupt playback
STOP 9
– to stop playback
Cassette Control
0
– to start recording
B
– to start cassette playback
Q
– fast rewind
MIC
R
– fast forward
9//
– to stop and eject the cassette
;
– to interrupt playback/recording
CD Display
PROGRAM
REPEAT
1
PLAY
PAUSE
PROGRAM:
programme playback
PLAY:
PLAY
PAUSE:
PAUSE
REPEAT 1:
repeat one
REPEAT:
repeat all
RADIO
Radio aerials
– For FM, pull out the telescopic aerial. To improve
FM-reception, incline and turn the aerial. Reduce
its length if the FM-signal is too strong (very close
to a transmitter).
– For MW/LW, the set is provided with a built-in
aerial, so the telescopic aerial is not needed.
Direct the aerial by turning the whole set.
Radio reception
• Set the FUNCTION switch to RADIO.
– The POWER indicator
6
lights up.
• Adjust the sound using the VOLUME, UBS and
SURROUND SOUND (only RR 650 CD) controls.
• You may connect stereo headphones having a
3.5 mm plug to the jack
p
.
– Inserting the plug will disconnect the speakers.
• Select the wave band using the BAND selector.
• Tune to a desired radio station using the
TUNING control.
6
– When FM STEREO
appears, you are
receiving a FM stereo transmitter.
• A disturbing noise, due to a weak FM stereo
signal, can be suppressed by setting
FM MONO/STEREO to FM MONO.
– The FM STEREO indication
6
goes out and you
will hear the FM station in mono.
• The set is switched off when the FUNCTION
switch is in the TAPE position and no buttons are
pressed.
–The POWER indicator
6
goes out.
p
.
CD PLAYER
Playing a CD
• Press PLAY/PAUSE 2; to start playback.
– The display shows 'PLAY' and the track number.
• Adjust the sound using the VOLUME, UBS and
PLAY
SURROUND SOUND (only RR 650 CD) controls.
• For brief interruptions, press PLAY/PAUSE 2;.
– 'PAUSE' appears on the display.
• To resume playback, press PLAY/PAUSE 2;
PLAY
again.
PAUSE
• To stop playback, press STOP 9.
– The total number of tracks will then appear on
the display.
– The CD player also goes to position STOP:
– by pressing OPEN/CLOSE;
– when the end of the CD is reached;
– if the batteries run down or if the power supply
is interrupted.
• To take out the CD, open the CD door by pres-
sing OPEN/CLOSE.
• Open the CD door only if the CD-player is in
position STOP.
Selecting another track during play
• Press ∞/5 or 6/§ until the required track
number appears in the display.
– The selected track begins to play.
Starting with a particular track
• Press ∞/5 or 6/§ until the required track
number appears in the display.
• Press PLAY/PAUSE 2;.
– Play starts from the selected track.
CD PLAYER
Checking the programme
Cassette recording
• Press 9// to open the cassette holder.
• From the STOP position, press PROG.
repeatedly: the display shows in sequence all
• Insert the cassette.
programmed track numbers.
• When monitoring during
recording, adjust the sound
Adding tracks to the programme
using the controls VOLUME,
• Press PROG. repeatedly until the display shows
UBS and SURROUND
'00'.
SOUND (only RR 650 CD) .
• You can now add tracks to the sequence as
These controls do not affect the recording.
described above (up to 21).
• Start recording by pressing 0.
(the B button is automatically also pressed).
Playing a programme
– When the end of the tape is reached, the
• Press PROG. once to show the first track of the
recorder buttons are released.
programme.
• To interrupt recording, press
• Press PLAY/PAUSE 2;.
• To continue recording, press
– Play starts with the first track of the programme.
• Press 9// if you want to stop recording before
– The display shows 'PROGRAM PLAY'
– After the last track playback stops.
the end of the tape.
– The total number of tracks will then appear on
On pressing again, the cassette holder will
the display.
open.
Note:
• The set is switched off if the FUNCTION switch
• Press STOP 9 to stop playback.
is in position TAPE and no buttons are pressed.
– The POWER indicator
6
• While playing a programme, it is possible to use
∞/5 or 6/§ to select the desired
programmed tracks.
Erasing a programme
• Press STOP 9 to stop playback.
• You can then erase the programme:
– by opening the CD door using OPEN/CLOSE;
– if you move the FUNCTION selector;
– if the batteries are exhausted or if the power
supply is interrupted in another way.
Searching for a passage during play
• Hold ∞/5 down to search backwards to the
beginning.
• Hold 6/§ down to search forwards to the end.
Note:
This function can be described as "audibly"
searching for a title.
During the search, volume is reduced and returns to
its adjusted level as soon as the button is released.
Repeating a track
REPEAT
1
• By pressing REPEAT once, one track is repeated.
PLAY
– The display shows: 'REPEAT 1'
Repeating the CD
• By pressing REPEAT once more, all tracks are
REPEAT
repeated.
PLAY
– The display shows: 'REPEAT'
• To switch the repeat mode off, press REPEAT
one more time.
Programming
By programming the player you can play up to 21
tracks in any desired order. If you exceed the
maximum of 21 tracks, the programme function will
start again from the beginning.
Storing a programme
• In STOP mode, press PROG..
The display will show '00'.
• Select the first desired track using ∞/5 or
6/§.
• Store this track by pressing PROG. again.
• Select and store in this way all desired titles.
CASSETTE DECK
Recording from the CD-player
(CD synchro recording)
• Set the FUNCTION switch to CD.
• It's not necessary to start the CD player se-
parately: by pressing 0 the CD player starts
automatically.
– If the CD player is in STOP position, recording
will start from the beginning of the CD (or from
the beginning of the programmed selection).
• To start a recording in the middle of a track,
play the CD in the normal way.
• As soon as the desired passage is reached,
;
.
pause the CD and then start recording by
pressing 0.
;
again.
Recording from the radio
• Set the FUNCTION selector to RADIO.
• Select the wave band using the BAND switch.
• Tune to desired radio station using the
TUNING control knob.
• In case of FM radio recordings, set the
goes out.
FM MONO/STEREO switch to the desired
position.
• If during the recording of an MW/LW station,
a whistling sound is heard, this sound can be
suppressed by setting the BEAT CUT switch to
another position.
Mono recording from the built-in microphone
• Set the FUNCTION switch to TAPE
• Set the VOLUME control to the minimum
volume level (during microphone recording ,
monitoring is not possible).
• To ensure a clear recording, the distance to
microphone should be 30 – 100 cm.
Werbung
Inhaltsverzeichnis
