Joyetech eGo One CT Anleitung

Notice for Use:
Thank you for choosing Joyetech products!
Please read this manual carefully to ensure proper use For any additional
product Or its use, please consult your local Joyetech retailer, Or visit our website at www_joyetech corn.
Product Introduction:
Equipped with Joyetech Constant Temperature technology,
(Nickel 200)/ CW mode in five fashionable colors, which enables you to have various options of atomizer heads.
eGo ONECT English
How to Use
1. Power on/off:
Press the fire button 5 times in quick succession
In the same way, the device will be powered off after 5 presses
2Shift Between CT-Ni/CT-Ti/CW Modes:
In power off condition, long press the fire button to shift among CT-Ni, CT-Ti and CW
modes within 2 seconds. And release the fire button to preserve the current mode
Note: (a) n CW mode, different resistance of coil matches different output as follows:
(b) In CT mode, different types of coil has different temperature
(c) Under CT mode, please install the temperature control coils at room temperature
3
eGo ONE CT
before the first use to reach the best performance
To protect the cotton from burning, please stop
vaping when the device is running out of e-juice
4. e-Juice Filling: Separate the atomizer from the
battery and inject the e-juice directly into the
cambered slot (i)
5. Atomizer Head Replacement: Unscrew the
atomizer cone, you' I see the atomizer head
ocated on the base. Then unscrew the head
with a replaced one. (2)
(Note: Do avoid cleaning the atomizer head with
water, simply wipe it with alcohol cotton or dry cloth)
5 eGo ONE CT
Atomizer Protection: eGo One CT is equipped with a 10 seconds run time protection. The light will flash 10 times if
the fire button is pressed for more than 10 seconds
No Atomizer Alert: If you press the fire button without atomizer, the current mode light will flash slowly, indicating
there is no atomizer.
Low Voltage Protection: When the battery vo tage is lower than 3 3V, the bottom light flashes for 40 times and the
battery will be locked. As soon as charging has commenced
Battery Display Function: When powered on, press the fire
button then release, the mode light-indicator will flash slowly
or stay lit when the battery quantity is high, on the contrary,
it flashes in frequency
eGo ONE CT
7
in usage manual)
* Merchandise failure or damage caused by improper use of water or other liquid (see usage manual for operating instructions)
* Merchandise failure or damage due to usage with non-Joyetech
3 This warranty does not cover personal items or consumable
mouthpiece, cartridge, atomizer head, lanyard, and leather sheath
4 This warranty does not cover any non-Joyetech
brand products during the warranty period of 90 days after date of purchase as indicated on proof of purchase
Joyetech reserves the right of final decision in all warranty
Joyetech may interpret and revise the content
eGo ONE CT
9
information or questions
eGo One CT, presents you with CT-Ti (Titanium)/
to turn the device on
as fol ows:
;
low voltage protection will be unlocked
Batte Quanti Li
300/0-590/0 Slowly flashes
100/0-290/0 Moderately flashes
lashes In requency
components (charger, battery, and power cable)
goods and attachments, including
brand products This warranty is only valid for eligible Joyetech
cases.
of this warranty terms.
Specification
Length: 108.0/140 Omm
regarding this
Atomizer Capacity: 1 812.5m
Battery Capacity: 1100/2200mAh
Output Mode: CT-NilCT-Ti/CW
Resistance Range:
CT-Ni
0 2-1 Oohm for CT mode
0.4-3.50hm for CW mode
0 4-0 80hm
25W
(d) Only use temperature
accidentally used under CW mode.
(e) CT mode only supports a maximum of 1 Oohm It will automatically
1.Oohm or using a normal coil under CT mode
(f) n CT mode, coils below 0 50hm are recommended
3. Soak the Atomizer Head:
When using a new atomizer head, please drip a few drops of e-juice in the cotton of atomizer head to ensure it is moist
6. Adjustment of Air Inflow:
counterclockwise to enlarge it.
7. Charging:
Simply charge the eGo One CT by connecting it with a PC Or wall adapter via USB cable Once plugged in, the charging
indicator will on and the current mode light flashes 5 times. When it is fully charged, the charging indicator will go out.
It takes about 3 hours (1IOOmAh)/5 hours (2200mAh) to charge the eGo ONE CT
Function:
Short Circuit Protection:
1. When the short circuit occurs before working, the current mode light flashes for 5 times and there will no output.
2. When the short circuit occurs while working, the button light flashes for 3 times and the output stops
Warranty terms
Please consult your Joyetech product warranty card. We are not responsible
Our warranty is not valid for products purchased from third party vendors
Joyetech agrees to provide
1. This warranty provides repair free Of charge for defective Joyetech brand merchandise.
from date Of purchase by the end user
2 This warranty may be void as a result Of any Of the fol Owing conditions:
Customer does not provide warranty card and original receipt Of purchase
ht Condition
Merchandise failure or damage is caused due to improper use or unauthorized
Sta lit
Merchandise failure or damage as a result Of excessive force such as dropping
Merchandise failure or damage as a result Of usage outside Of recommended
but not limited to:
Diameter: 19 Omm
Mode
CT Battery Atomizer Base
081-1 60hm 161-3 50hm
15W
control coils under CT mode. Damages will be caused when temperature
switch to CW mode when the coil is larger than
for CT-Ti mode, and coils below 0 30hm for CT-Ni mode.
Rotating the ring clockwise on the atomizer
(3)
repair under warranty pursuant to the following
CL-Ti Head CL-Ni Head
(0.40hm) (0.20hm)
CL Head
(I _00hm)
Atomizer Tube Mouthpiece
English eGo ONE CT
2
CT-Ti CT-Ni
4700F 480ØF
control coils are
English ONECT 4
base to decrease the air inflow, while
(reset)
eGo ONE CT 6
for any damage caused by user error
terms and conditions:
Warranty period is 9() days
repair
operating conditions (see precautions
eco ONE CT 8