SUNLU FilaDryer S2 Bedienungsanleitung

SUnLU
FilaDryer S2
3D PRINTING-MATE
Drying while printing to improve your 3D model.
-sv 58t
— PLR
sunw
EN/ DE/FR/IT/ES/JP
C€IFC RoHS
Zhuhai Sunlu Industrial co. , Ltd.
Official website: www.3dsunlu.com
Brand cooperation: branding@sunlu.com
Business cooperation: sales@sunlu.com
After-sales service: support@sunlu.com
Address; 38,Yongtian Road,Fuxi Industrial Zone,
Xiangzhou District,Zhuhai Guangdong,China.
Note: Read this document before using the
filament dryer
• Do not place the product where children can reach.
• Pay attention
product near water, such as in the bathroom,
other places where water is easily accessible.
• Only use the original power adapter or a fully certified 24V/2A power
adapter.
• Switch off the power
sudden fire.
• Place the two rollers in the box before operating the dryer.
• Confirm filament
prevent it from falling onto the heat sink, resulting in high temperature
deformation of the filament.
• When drying
sensitive objects.
• Do not touch the heaters in the oven when drying filament
burns.
• The upper lid of the drying
consumables to avoid
• In order to ensure the drying effect, do not open the drying box at will
during operation.
• If there is a fault with the product , disconnect
the filament dryer and the electrical socket then contact the after-sales
support team.
Product specifications:
Product size
Maximum capacity
Net weight
Working environment
Temperature setting range
Power adapter specifications
Standby power
Maximum working current
Maximum working power
LCDdisplay screen
Suitable for filament
Product function
MADE CHINA
EN
to electrical safety during operation. Do not use this
bathtub, wash basin and
supply when not using this product
tightly wound to the roll before using this product to
filament, do not place the products on temperature
oven should be covered when
heat loss.
the power adapter from
265 X 274 X 118 (H) mm
$210 • 85 (H) mm
Ilgog (includingpower adapter)
a) Environment t emperature: 20 oc 35 oc
b) Relative humidity S
35
a) specifications; AC IDOV 240V, 50 / 60Hz
b) Output specifications: DC:24V t 1.2V, 2A
0.05M/
1.9A
48W
4.6-inch LCDdisplay
1.75mm/2.85mm
diameters
diagram:
Displaycontrol panel
LED light circle
to avoid
Schematic Diagram of the Content Displayed
on the LCD:
Measured Temperature
Cursor Column
—SV: 888
to avoid
—Time: B B.8B.8B
— Material:
drying
— LED OFF
Touch Button
www
DC24V
Operation Guide:
1. Power On
Plugthe power adapter attached to this product into the power supply,
and then connect the power cord to the DCpower socket of the dryer.
The dryer is in standby without heating state by default after the power
is connected, and the screen
2. Filament Loading
Placethe filament in the dryer, pull the thread out of the outlet and close
the lid tightly. (Note: Please make sure that the consumables are in a
tightly wound state).
3. Turn On the Dryer
Clickthe Z',the dryer will work accordingto the default settings
(Temperature: 50 C, drying time: 6 hours, material: PLA,LED:OFF)
4. PersonalizedSettings
A.This product can change the temperature unit.
Click the when the cursor on the left side of the PV flashes, click
You can switch between Fahrenheit and Temperature
Celsius.
B.Thisproduct can increase or decrease the temperature according to
personal settings (temperature setting range: 35 C
Click the" when the cursor on the left side of the SV flashes, click
" o " , the temperature
3 seconds of stopping the operation, the dryer will automatically save the
set temperature.
In addition, you can
DCpower socket (24V 2A)
Measured Humid'
Temperature Setting
CCF
Drying Time
Selection of Drying Materials
ON RUN
Working Mode of LED
2A Port
C).
can be increased or decreased. After
without the cursorflashing.