Renkforce Riva 1274644 Bedienungsanleitung Seite 3

Operating instructions
LED floor lamp Riva,10.5 W
Item no. 1274644 (40 cm)
Item no. 1274683 (60 cm)
Intended use
The product is suitable for outdoor installation (protection type IP44) and is intended
for lighting entrance areas, patios, etc.
For safety and approval purposes (CE), you must not rebuild and/or modify this product.
If you use the product for purposes other than those described above, the product may
be damaged. In addition, improper use can cause hazards such as short circuiting,
fire, electric shock etc. Read the instructions carefully and keep them. Make this
product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All
company names and product names are trademarks of their respective owners. All
rights reserved.
Delivery content
• LED floor lamp
• 3 x screws
• 3 x dowels
• Operating instructions
Symbol explanation
The symbol with a flash in a triangle indicates health risks e.g. due to electric
shock.
This symbol warns you about specific risks when handling, operating or
using the product.
The "arrow" symbol indicates special remarks and notes for operation.
The light is not dimmable.
Follow the operating instructions!
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information on
proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the
warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets. This
poses a risk of fatal electric shock!
• Do not leave packaging material lying around carelessly. These may
become dangerous playing material for children.
• Operate the product only via a common household power supply of
220 – 240 V/AC, 50 Hz.
• The product is only suitable for fixed installation.
• The product must not be used in areas prone to flooding. The same applies
to areas (e.g. troughs), in which rainwater can collect.
• Never point a garden hose at the product.
• The product may not be mounted in or under water.
• Do not operate the product with a dimmer.
• Attention, LED light:
- Do not look directly into the LED light!
- Do not look into the beam directly or with optical instruments!
• Protect the product from extreme temperatures, strong jolts, flammable
gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of
operation and protect it from any accidental use. Safe operation can no
longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a
low height can damage the product.
• For installations in industrial facilities, follow the accident prevention
regulations for electrical systems and equipment of the government
safety organization or the corresponding authority for your country.
• Consult an expert when in doubt about operation, safety or connection of
the device.
• Maintenance, modifications and repairs are to be performed exclusively
by an expert or at a qualified shop.
• If you have questions which remain unanswered by these operating
instructions, contact our technical support service or other technical
personnel.
Preparing installation
Installation of the product must be carried out by a qualified professional
(i.e. an electrician) who is familiar with all applicable regulations!
By handling mains voltage improperly, you endanger not only yourself but
also others!
If you do not have the relevant expert knowledge, do not install the product
yourself, but have it done by a professional.
• The product is suitable for use in unprotected outdoor areas. It must however not be
used in or under water. This poses a risk of fatal electric shock!
• Protect the product from salt water (e.g. road salt in wintertime) in order to prevent
corrosion.
• Mount the product to a horizontal surface only.
• Do not mount the product to or inside vehicles.
• When mounting the product, take into consideration the routing of the mains cable.
• Only use a suitable, fixed mains cable for power supply.
• A suitable switch is required for turning the product on and off.
• The product must be secured via an existing sub-distribution unit with a 10/16A fuse.
This setup requires the installation of an upstream residual current circuit breaker
(FI switch).
• The product must be completely free of voltage for installation. Just turning off the
light via the switch does not make it entirely voltage-free.
• Turn off the corresponding circuit breaker and/or automatic fuse to remove all
voltage from the power circuit. Secure them against unauthorized restart, e.g. by
installing a warning sign. Also switch off the relevant circuit breaker in order to
disconnect all poles of the mains cable from the mains supply.
• Check the power circuit for any remaining voltage using an appropriate measuring
device.