Renkforce 1094558 Bedienungsanleitung Seite 3

G Operating Instructions
Bluetooth music receiver
®
Item no. 1094558
Intended Use
The device is used for the wireless reception of audio data via Bluetooth
process, the audio signal is provided either on the 3.5 mm jack output or on the optical
S/PDIF connector.
Any device that supports Bluetooth
can be used for the transmission.
Read these operating instructions completely and carefully as they contain very im-
portant information about installation, operation and handling. Observe all safety in-
structions!
Package contents
• Music receiver
• Wall plug transformer
• Audio cable 2x 3.5 mm phone jack
• Adapter cable 3.5 mm jack socket on 2x cinch plugs
• Operating instructions
Safety Instructions
D amages due to failure to follow these operating instructions will void the
warranty/guarantee. We do not assume any liability for any resulting dam-
age!
W e do not assume any liability for material and personal damage caused
by improper use or non-compliance with the safety instructions. The war-
ranty/guarantee will be void in such cases!
Dear customer,
The following hazard information and safety instructions are intended not
only to protect your health but also to protect your device. Please read the
following points carefully:
• The design of the wall plug transformer complies with Protection Class II.
• The mains socket for the wall plug transformer must be located in direct
proximity to the device and easily accessible.
• The product and the wall plug transformer are suitable only for dry indoor
areas. Do not expose these product components to direct sunlight, heat,
cold, dampness or wetness; otherwise they may be damaged.
The wall plug transformer poses the risk of a potentially life-threatening
electric shock!
• This product is not a toy. Devices operated using mains voltage should
not be used by children. Position the product so it is out of the reach of
children.
• Handle the product with care; it can be damaged by impacts, blows, or
accidental falls, even from a low height.
• Do not pull the wall plug transformer from the mains socket by pulling on
the cable.
• Do not touch any wall plug transformer that shows signs of damage; there
is a danger to life from electric shock!
First, switch off the power supply to the mains socket to which the wall
plug transformer is connected (e.g. switch off at the corresponding circuit
breaker or remove the safety fuse and then switch off the corresponding
RCD). Now disconnect the wall plug transformer from the mains socket
and take the product to a specialized workshop.
• Do not leave packaging material carelessly lying around, since it could
become a dangerous plaything for children.
3.0 and is able to playback audio files and videos
®
Connection and commissioning
• Before you can begin, unpack the product and its accessories.
• First, connect your audio device to the music receiver.
To this end, use the 3.5 mm jack output e.g. to connect your stereo equipment or PC
loudspeaker analogously to the product. You may also connect a headset with a 3.5
mm stereo jack directly to the device.
If your device to which you want to connect the receiver features an optical Toslink
input, we recommend you to use it. In that case, the audio signal will be transmitted
digitally. It might be necessary to enable the S/PDIF input on your household device
first. Please observe the operating instructions of the device in question.
• Connect the wall plug transformer to the power socket of the device and then insert
it into a power outlet. Once the device has started, the blue LED flashes once every
5 seconds and thus is ready for connection.
Establishing the Bluetooth
• Enable Bluetooth
®
receiver. With an Android smartphone for example, you can find this function under
. In this
®
"Settings" in the section "Connections". With Apple iOS you will find this function
under "Settings" in the section "Bluetooth".
• Once the device "Music receiver" is displayed, select it in order to connect e.g. your
smartphone to the receiver. If no other device is connected to the music receiver,
the latter will be automatically selected for the audio playback. Once the connection
has been established, the blue LED lights up permanently.
Attention. Even though multiple devices can be connected to the receiver
via Bluetooth
back. If you wish to use another device, you first have to disable the other
one.
Playback
• Now you can playback any audio file on your device. The sound will be automati-
cally output on the Bluetooth
to switch the audio output between the Bluetooth
you are using to playback the audio files.
• Of course, you can also playback videos. In this process, the image is displayed e.g.
on your tablet and the sound on the receiver or on the device connected to it.
• The control of the playback and the volume is done via your smartphone or tablet, as
usual.
Disconnecting the Bluetooth
• To disconnect your device from the receiver, navigate to the Bluetooth
again and disable the connection. Alternatively, you may simply switch off the Blue-
tooth connection.
®
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare
that this product conforms to the fundamental requirements and other relevant regula-
tions of the directive 1999/5/EC.
The Declaration of Conformity for this product is available at
www.conrad.com.
Maintenance and Cleaning
The product is maintenance-free. Maintenance or repair work may be performed only
by qualified personnel or a specialised repair shop. The product contains no parts that
require servicing. Therefore, do not open it.
To clean the outside of the product, a dry, soft and clean cloth is sufficient.
Dust can easily be removed using a clean, long-haired brush and a vacuum cleaner.
Do not use abrasive cleaning agents, cleaning alcohol or other chemical
solutions, since these could damage the casing or even impair operation.
Disposal
Electrical and electronic equipment do not belong in the regular household
waste.
Dispose of the waste product in accordance with the applicable legal regu-
lations.
connection
®
on the device you want to use to transmit audio data to the music
, only one of them can be enabled and used for the audio play-
®
receiver. Depending on the device, it is also possible
®
music receiver and the device
®
connection
®
settings
®