Identification Of Parts; Assembly; Use Of Accessories; Changing From Trimmer To Brush Cutter - Texas Andreas Petersen BCU33M Bedienungssanleitung

Identification of parts

A: Engine
B: Harness
C: Pruner
D: Hedgetrimmer (Adjustable 135°)
E: Brush Cutter
F: Grass Trimmer

Assembly

Mount the handle as shown in Fig 2A. Ensure that
the machine is in balance and bolts are tighten.
Attach the middle tube to the machine, fasten with
butterfly knob. See fig 2B.
Attaching the:
Pruner
C. Attach the pruner to the middle tube and fasten.
See Fig. 2B.
To mount the bar and chain, see Fig. 11.
To loosen/tighten the chain, the adjustment
screw in front of the saw is used. See Fig. 12.
It is recommended to check and add chain
oil every 30-45 min.
Hedge trimmer
D. Remove the protection cap from the hedge
trimmer unit. Attached the tube into the hedge
trimmer. See the small hole on tube to know
which direction goes in. Tighten the screw.
Attach the hedge trimmer to the engine unit and
fasten. See Fig. 2B.
The hedge trimmer tube can be placed in a
transport angle by loosening a screw (see Fig.
2C). When the hedge trimmer is being used, the
tube must be turned back in work-position (see
Fig. 2D) and the screw must always be tighten
again before use.
Brush cutter and Grass trimmer
E/F. Attach the Brush cutter and Grass trimmer to
the machine and fasten. See fig 2B.

Use of accessories

Pruner
•
Do not use the saw (pruner) standing on a
ladder or another aid in unstable position.
•
Beware of falling branches.
Hedge trimmer
•
Hedge scissors may be used not only on hedges
but also to cut shrubs.
•
The best cutting output may be obtained when
the scissors are conducted at an approximate
angle of 15°to the hedge.
•
To obtain an even height of the hedgerow, it is
recommended to have a conducting cord
stretched along the hedge.
•
Side surface area of the hedge will be trimmed by
arched movements from down and upwards.
•
Clean the unit after every use and check all the
integrated tools and protection devices for
damages.
Brush cutter and Grass trimmer
•
When the engine is stopped the rotating blade
must be held in grass or bush until it holds still.
•
Always hold the machine with both hands.
•
The machine must not be used if the safety
guard is not correctly fitted and in mint condition.
•
Always stop the engine before attempting to
remove objects that may have stuck on the
blade.
•
Never touch or try to stop the blade while it is
still spinning.
•
A rotating blade may cause damage, as it
continues to spin after the engine has stopped
or the gas has been turned off. Always be in
control of the tool until the blade has stopped
spinning.
•
Always make sure that the blade is mounted
securely and correctly before every time it is
used.
•
Only use a sharp blade. Replace blades that are
worn or damaged.
•
Only use original spare parts.
•
Only use the blade for weeds, grass and similar.
•
Kickback is something that may occur when the
rotating blade gets into contact with something,
it cannot cut. This contact may have the effect,
that the blade stops for a moment, and suddenly
the tool is thrown away from the hard object that
was hitting. This reaction may be so violent that
the user loses control of the tool. Kickback may
occur without warning if the blade is stuck, loses
speed or impeded. This is most likely in areas
where it is difficult to see the material that is
being cut.
•
The harness must always be used and adjusted
to fit in the correct manner.
•
Keep a firm grip on both handles while the blade
is running. Keep the blade away from your body
and below your waist.

Changing from trimmer to brush cutter

Dismounting the trimmer head See Fig 4B
1. Fit the Allen key (2) in the hole of the gear (3) to
lock the gear in place.
2. Turn and remove the trimmer head (1) from the
shaft.
3. Washers can now be removed.
Notice: Keep the parts for the trimmer head
together for later use.
14