Grundig R 23 DPL Serviceanleitung Seite 6

ADAPTING THE SURROUND MODE VALUES
Adapting the Surround mode values
> 1.5 SEC
The surround mode has programmed values for
VID 1 PROLOGIC
centre-mode, centre and rear levels and for rear SURROUND
channel time delay which are suitable for most
VID 1
NORMA L
common applications.
#
You can , however, change these settings to your
TUNING / STATION
particular taste or speaker installation. $
To install your Surround system proceed as
follows: VID 1 DELAY 15
SURROUND
• Select the Dolby Pro Logic mode.
#
• Press the SURROUND key longer than 2
TUNING / STATION
seconds.
$
– The display shows e.g.'NORMAL'.
• Use the # $ (TUNING or STATION) buttons to
VID 1 TESTTONE
select the centre channel mode: NORMAL,
SURROUND
VID 1
WIDE or PHANTOM. TEST F L
– Select NORMAL if you are using a normal
#
VID 1 TEST C
centre speaker.
TUNING / STATION
$
– Select WIDE if you have connected a HiFi
VID 1 TES T FR
centre speaker
#
– Select PHANTOM if you have not connected a
VID 1
TUNING / STATION
centre speaker, but still wish to simulate the
$
sound coming from the centre.
• Press the SURROUND button again.
– The display shows e.g. DELAY 20.
VID 1
REAR
REAR/–
• Use the # $ (TUNING or STATION) buttons to
adjust the delay time of the rear channel
REAR/–
(15, 20 or 30 ms).
Increasing the rear delay time expands the
perceived listening area, and vice versa.
VID 1 CTR
CENTRE/+
REAR/–
STATION MEMORY
Storing Preset Stations
You can store up to 30 stations in the memory.
When a preset station is selected, the preset num-
ber appears next to the frequency on the display.
Automatic programming
• Press MEMORY for more than 1 second.
– flashes on the display.
MEMO
TUNED STEREO
– Every available station will be stored automati-
F M 9 7 2 5
cally. The frequency and preset number will be
displayed briefly.
– It will stop searching when all the available
stations are stored or the memory for 30 preset
stations is used.
– The set will remain tuned to the last stored
preset number.
• You can cancel the automatic programming by
pressing MEMORY again or any other key on
the unit.
TUNED STEREO
BAYERN 3
Note: If you want to maintain some old preset
RDS
numbers, for example preset number 1 - 9, select
PTY
RT
preset 10 before starting automatic program-
TUNED STEREO
13
ming: now only the preset numbers 10 to 30 will
RDS
PTY
be programmed.
RT
TUNED
ARD-RADI
Manual programming RDS
PTY
RT •
• Press briefly MEMORY for less than 1 second. TUNED
FM
– flashes on the display.
MEMO RDS
PTY
RT
• Press TUNING # or $ to tune to the desired
frequency.
• Press STATION # or $ to select a preset
F M 8 7 5 0
number.
• Press MEMORY again.
TUNED STEREO
F M 9 3 0 0
– stops flashing, and the station is stored.
MEMO
• Repeat the above procedure to store other
preset stations.
• Press the SURROUND button again.
– You will now hear a test tone from the left,
PRO LOGIC
centre, right and rear speakers in turn, in a
repeating cycle.
PRO LOGIC
– The display shows e.g. TEST FL TEST C
TEST FR TEST R TEST FL
• The values of the centre and rear level can be
adjusted if you press # $ (TUNING or
STATION) during the 2 seconds that you hear
PRO LOGIC the test tone of the centre TEST C and the
rear speaker TEST R.
• When you are satisfied with the levels, press
the SURROUND button again to turn off the test
tone and leave the installation mode.
PRO LOGIC Note: When you have selected PHANTOM for the
centre channel mode, the test tone sequence will be
PRO LOGIC
as follows: TEST FL TEST FR TEST R
TEST FL
PRO LOGIC
Direct adjustment of rear and centre level
PRO LOGIC
During e.g. a film, it is possible that the special
PRO LOGIC effects on the rear speakers become too loud or
TE ST R
too quiet compared to the level of the dialogue,
making it necessary to perform small adjustments.
Your remote control is, for this purpose,
provided with two keys for direct adjustment:
Adjusting the rear level
PRO LOGIC
0
• Press the – REAR button.
The display shows e.g. REAR 0.
CENTRE/+
• If you press within 2 seconds the CENTRE + or
– REAR buttons you can adjust the rear level
(related to the front level).
Adjusting the centre level
PRO LOGIC
• Press the CENTRE + button.
0
The display shows e.g. CTR 0.
• If you press within 2 seconds the CENTRE + or
CENTRE/+
– REAR buttons you can adjust the centre level
(related to the front level).
Calling up a stored station
• When you want to call up a stored station,
press STATION # or $ on the unit or on the
remote control.
– The stations are called up in ascending or
descending order.
Deleting all stored stations
MEMO
• If you wish to delete all stored stations, for
MHz
example after you move to another location,
PRESET
press first MEMORY.
– flashes on the display.
MEMO
• Press now at the same time the buttons TUNER
and MEMORY.
– All stored stations have now been cleared and
the display shows 'FREE'.
Changing display indication:
• Pressing INFO on the unit or TXT/ on the
remote control briefly switches the display
mode between (when available) station name,
PRESET
45 RDS-time, RADIOTEXT, and frequency.
PRESET
STEREO
PRESET
STEREO
9790
MHz
PRESET
MEMO
MHz
MEMO
MHz
PRESET
RADIO
RDS Radio Data System
Your receiver is an RDS receiver.
FM
It is capable of receiving and evaluating RDS
information which is broadcast along with the
normal broadcast signal providing the listener
with more comfort and extra usefull information.
You can also call up other RDS services like RDS
time and radiotext provided that this information
TUNED
is transmitted.(button INFO, see page 25). FM
RDS Station name : If you are tuned to an RDS
station, the name of the station will be indicated
after a short time, overwriting names previously
stored.
RDS TIME : Some RDS stations broadcast the
'RDS-TIME' information. The time display is
updated every minute. The accuracy of the time
depends on the broadcasted information.
RADIOTEXT : More and more RDS stations
broadcast RADIOTEXT, which is additional
F M 93 00
information on the station and programme being
broadcast. RADIOTEXT information appears as
FM
"running" text in the display. RADIOTEXT is
transmitted character-by-character by the radio
TUNED
FM
station. As a result of that it may take some time
until the entire text has been completely received.
PROGRAMME TYPE : Each station can broadcast
a code (PTY) that characterizes the actual
program. With the PTY button you can select the F M 97
type of programme you wish to listen to.
FM
FM reception STEREO/MONO
TUNED
Still, there are stations with disturbances or noise F M
in the audio signal, due to a weak signal.
• When the FM reception is disturbed, press
MONO. Now the mono function will reduce
noise due to weak reception.
– appears on the display.
MONO
SYSTEM REMOTE CONTROL
Changing the batteries
If the range of your infrared remote control seems to
decrease, or if certain individual functions can no longer
be carried out, you should replace the batteries.
Two micro 1.5 Volt LR03 size AAA are required. To
change the batteries, open the compartment on the
back of the remote control. Ensure that the batteries
are inserted properly (note the markings in the
compartment).
In the interest of the environment:
Remember that batteries must always be
disposed of properly.
General controls
y HIFI – To switch the HIFI system to STAND BY.
VOLUME +/– – Controlling the volume of the
amplifier.
– For muting the speakers.
SURROUND INST This button is used to switch
between SURROUND and STEREO mode and to enter
the installation mode for surround settings.
REAR – to call up rear level adjustment mode or to
manipulate the different surround settings
CENTRE + to call up centre level adjustment mode or
to manipulate the different surround settings
TUNING TO RADIO STATIONS
Automatic tuning
• Press TUNER on the unit or remote control.
8 7 50
– The display shows the current frequency in the
MHz
FM waveband.
• To activate automatic station search, press
TUNING # or $ until the frequency display
begins 'to run'; then release the button.
– The search stops as soon as a station with
STEREO sufficient reception quality is found.
8 8 00
– lights up when a station is tuned to precisely.
MHz TUNED
– The frequency of the received station is
indicated in MHz (FM).
– Stations which are received with a weak field
strength may be skipped. These can be tuned
to manually.
• If desired, you can also interrupt the search by
pressing TUNING # or $.
Manual tuning
• Briefly press the TUNING # or $ button to tune
MHz
in the corresponding direction in individual
9 30 5 steps (FM: 50kHz) until the display shows the
MHz
right frequency and/or until the best reception
STEREO has been obtained.
93 10
MHz
Direct Frequency input
If you already know the frequency of the desired
station, you can enter it directly.
• Select TUNER on the remote control.
MHz
– The display shows the current frequency.
9 75
• Enter the desired reception frequency in order,
MHz
from left to right, by using the numeric buttons
STEREO
97 50
0-9 on the remote control.
MHz
– After you have finished entering the last
number, your unit will receive the new station.
– You have 10 seconds to make each entry. If
this time limit is exceeded, you must enter it
again.
TUNER
TUNER– For selecting the radio and to assign the RC
commands to radio keys.
10-button keypad for directly selecting frequencies
$ # STATION – For selecting stations.
S T – To start tuning up/down.
TXT/ – To change the information shown in the
display.
PTY – For selecting the programme type (PTY) mode.
CD
CD – For selecting the CD player and to assign the
RC commands to CD keys.
10-button keypad for directly selecting tracks
; – To switch the CD player to PAUSE.
9 – To switch the CD player to STOP.
B – To start and restart playback of the CD player.
S T – To select next or previous tracks on a
CD, to search forward and backward.
DISC – To enter disc selection mode when using a
CD-changer.
TAPE
TAPE – For selecting the cassette deck and to assign
the RC commands to TAPE keys.
B – To start playback.
9 – To switch the cassette deck to STOP.
; – To switch the cassette deck to PAUSE.
S T – For fast winding of the tape in forward
or reverse direction or to search for next or previous
tracks during playback.
A B– For selecting the tape travel direction.
TXT/ – This button is used for switching between the
COUNTER (tape counter) and TIME (real time in
minutes and seconds) display.