Cameo ROOT PAR BATTERY Bedienungsanleitung Seite 9

SETTING DMX MODE
You can access the main menu by pressing MENU. Using the  and  buttons, now select the DMX Mode menu option and press ENTER
to confirm your selection. Use  and  again to select the desired DMX mode and press ENTER to confirm your selection. Press the MENU
once (1×) to return to the main screen. If there is no input within approx. two minutes, the main display is automatically activated. You can
find tables on channel assignment in the different DMX modes in these instructions under DMX CONTROL.
--------Menu-------
DMX Address ----DMX Address----
DMX Mode
DMX Address
001 - 512 001 - 512 001 - 512 3CH
DMX Delay
DMX Mode
5CH1
Stand Alone
DMX Delay
5CH2
Slave
6CH
Settings
7CH
System Info
10CH
DMX DELAY
The DMX Delay function allows a chaser light effect to be easily created with any number of spotlights of the same model and software
version, which could otherwise only be achieved with a suitable DMX controller and complex programming. All spotlights integrated into the
setup are set to the same DMX mode and controlled with the same DMX start address.
On the one hand, the delay time (delay time of DMX signal) can be set manually on each spotlight with a different delay time (DMX Delay by
DMX? No). On the other hand, the connected DMX controller on a specially reserved DMX channel can be used to set the same delay time
for all spotlights (DMX Delay by DMX? Yes).
Starting from the main display, press MENU to go to the main menu. Using the  and  buttons, now select the DMX Delay menu option
and press ENTER to confirm your selection. Use the  and  buttons again to select the desired submenu option, press ENTER to confirm
your selection, and set the value or status as desired. Press ENTER to confirm all entries.
--------Menu------- -------Delay-------
DMX Address Group
DMX Mode by DMX?
DMX Delay Delay
Stand Alone
Slave
Settings
System Info
Assign the spotlight to one of 15 groups (maximum number of groups depending on the activated DMX
mode). Several spotlights can also be assigned to one group. The group number is also the factor by which the set delay time is multiplied
(see setup examples).
Spotlight(group) 0
No delay
-------Delay-------
DMX
Group
Controller by DMX?
Delay
-------Delay-------
0 Group 0
0–15
No by DMX? No
0.0 s Delay 0.0 s
-------Delay------- -------Delay-------
Group 0 Group
No
by DMX? No by DMX?
Yes
Delay 0.0 s Delay
-------Delay-------
Group 0
by DMX? 0.0 s–2.0 s No
Delay 0.0 s
Spotlight(group) 1 Spotlight(group) 2
1.5 s delay
-------Delay------- -------Delay-------
0 Group 1 Group
No by DMX? No by DMX?
0.0 s Delay 1.5 s Delay
-----By DMX?-----
Warning! Delay
0
No
is controllable
No
Yes
by DMX now!
0.0 s
Spotlight(group) 3
3 s delay 4.5 s delay
-------Delay-------
2 Group 3
No by DMX? No
1.5 s Delay 1.5 s
-------Delay-------
Group 3
by DMX? No
Delay 1.5 s
-------Delay-------
Group 3
by DMX? No
Delay 1.5 s
-------Delay-------
Group 0
by DMX? Yes
Spotlight(group) 4 Spotlight(group) 5
6 s delay 7.5 s delay
-------Delay------- -------Delay-------
Group 4 Group
by DMX? No by DMX?
Delay 1.5 s Delay
5
No
1.5 s
9