Maintenance And Cleaning - Radleys Carousel Betriebsanleitung

3•wire connectingcables:
Here thetest c urrent circuit canalsobeproduced i ntheterminal head
ofthecontact thermometer
A 3-wire c able with therequired bridge i savailable (accessories).
The ratedtemperature i sset o nthecontact t hermometer by
means oftherotary m agnetic head, whereby theupper edge ofthetra-
velling n ut i sthereference point o ntherated v alue scale.
The required surface temperature of theheating plateispræ
selected onthetemp•rotaryknoboftheinstrument.
Ifthetemp-rotary
theheating-up
perature overshoots therated value setonthecontact thermometer.
Ifthetemp-rotary
value of 60octhetemp-rotary
good compromise
If thetemprotary knob is setprecisely totherated temperature,
medium d oes not r each therated temperature
perature between heating p late andmedium.
OntheCarousel Temperature Controller t heMtedtemperatu-
re isset b ypressing therotary k nob and byturning i tatthesame t ime.
When using t heETS-D,
rature owing toan"aiming-off allowance" technique.
Stirring Function
The stirring Function
The motor speed i ssei o ntherotary k nob "stirring" with itsdialfrom I
to10. I fthe motor isswitched
knob, and the LED " stirrer" beside the imprint "stiring" shines green.
CAROUSEL S tirringHotplate
(connect plugpins 2 and 3).
knob isset t othemaximally adjustable
takes p lace asrapidly a spossible, yetthemedium t em-
knob isset t otwice therated v alue (e.g. w ith a rated
knob isset t o 1200 C),theresult isa
between rapid heating-lip and overshooting.
owing toc dropintem-
there isnoovershooting of themedium t empe-
isstarted and stopped byits corresponding
on, i truns-up tothe speed set onthe rotary
Thedialfrom1 - 10conforms witha speed range from 50-1100
l/min.When idling, t hespeed i s1100Wmin atmaximum
therotaryknob(right-hand stop).
Iftheviscosity increases during t heprocess, thespeed d rops a little.
Iftheviscosity decreases,
speed increases a little.Bya corresponding
knob, b oth of these c ases c anbebalanced, aslongasthetorque
does not exceed its maximum.
Please note thatmains f luctuations
also effect minor F luctuations
temperature,

Maintenance and Cleaning

The CAROUSEL Stirring Hotplate ismainÉnacefree.
natural wear a nd tear o fcomponents
Whenode*lg spareparts,please givethemantfichJing
number shownonthetypeplate,themachine typeandthe
the
nameof the sparepan.
Please send i nequipment
isfree from any materials
cleansing agents which h ave b een a pproved byRadleys b clean t his devi-
ce. To remove use:
Dyes
Construction materialswater containing
Cosmetics
Foodstuffs
Fuels
For m aterials which a re not l isted, please request information
switch.
Wear theproper protective
Electrical devices may not b eplaced i nthe cleansing
ofcleaning
Before using other than t he recommended
mination, theuser m ust ascertain w iththemanufacturer
not d estroy theinstrument.
setting o f
e.g.duetoadding thinly fluid media, the
resetting of therotary
within thepermissible tolerance
ofthespeed
Itissubiect only tothe
and their s tafistical failure r ate.
forrepair only after i thas been cleaned and
which m ay constitute a health hazard. Use o nly
isopropyl alcohol
tenside / isopropyl alcohol
water containing tenside / isopropyl alcohol
water containing tenside
water containing tenside
from Radleys.
gloves during c leaning ofthe devices.
ogent forthe purpose
method for cleaning ordecontc
thatthis method d oes