Ryobi RTS4 Bedienungsanleitung Seite 3

EN ORIGINAL INSTRUCTIONS
Safety, performance, and dependability have been given top
priority in the design of your scrubber.
INTENDED USE
The scrubber is intended to be used only by adults who have
read and understood the instructions and warnings in this
manual, and can be considered responsible for their actions.
The product is intended for cleaning exterior and interior
surfaces. It can be used with water.
Do not use the product for any other purpose. Use of the
product for operations different from intended use could
result in a hazardous situation.
WARNING! Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
Save all warnings and instructions for future reference.
SCRUBBER SAFETY WARNINGS
Beware of splashing when using the product with water
or cleaning agents.
Maximum force that can be applied on the product
before stalling is 108 N at maximum torque and low
speed. Do not exceed the maximum force.
Switch off the product immediately if it stalls. Do not
switch on the product again while it is still stalled, as
doing so could trigger a sudden recoil with a high
reactive force. Determine why the product stalled and
rectify this, paying heed to the safety instructions.
use of a tool. When using any tool for prolonged periods,
ensure you take regular breaks.
Ambient temperature range for tool during operation is
between 0 °C and 40 °C.
Ambient temperature range for tool storage is between
0 °C and 40 °C.
The recommended ambient temperature range for the
charging system during charging is between 10 °C and 38 °C.
ADDITIONAL BATTERY SAFETY WARNINGS
damage due to a short circuit, never immerse your tool,
battery pack or charger in fluid or allow a fluid to flow
inside them. Corrosive or conductive fluids, such as
seawater, certain industrial chemicals, and bleach or
bleach-containing products, etc., can cause a short circuit.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national
provisions and regulations.
Follow all special requirements on packaging and labelling
when transporting batteries by a third party. Ensure that
no batteries can come in contact with other batteries
or conductive materials while in transport by protecting
exposed connectors with insulating, non-conductive caps or
tape. Do not transport batteries that are cracked or leaking.
Check with the forwarding company for further advice.
KNOW YOUR PRODUCT
See page 43.
1. Collet
2. LED indicator
3. Speed button
4.
5. Battery cap
6. Pivot button
7. Coupler
8. Cone brush with medium bristle
9. 90 mm brush with medium bristle
10. Handle, insulated gripping surface
11. Operator's manual
12. USB charging cable
13. Battery pack
14. USB power adaptor
LED INDICATOR
Product status
Operational
Low battery (5–25%)
Low battery (0–5%)
Over current protection
Over temperature protection
MAINTENANCE
The product should never be connected to a power
cleaning, performing maintenance, or when the
product is not in use. Disconnecting the product from
the power supply will prevent accidental starting that
When servicing, use only original manufacturer's
replacement parts, accessories and attachments.
Use of any other parts may create a hazard or cause
product damage.
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to various types of
commercial solvents and may be damaged by their
use. Use clean cloths to remove dirt, carbon dust, etc.
Do not at any time let brake fluids, gasoline,
petroleum-based products, penetrating oils, etc.,
come in contact with plastic parts. Chemicals can
damage, weaken or destroy plastic which may result
For greater safety and reliability, all repairs should be
performed by an authorised service centre.
LED indicator
Solid green
Solid red
3
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL