8BITDO SN30 Pro Bedienungsanleitung

8Bitdo@
SN30 Pro and SEO
8Bitdo'
Instruction
L',L2 Pair
SELECT
Opad
Star
Left Jo stick
• Press START to turn on the controller.
• Press and hold START for 3 seconds to turnoff
• Press and hold START for 8 seconds to force turn off the controller.
@ Bluetooth Connection
Switch
1. PressSTART+Y to turn on the controller, LEDswill start to rotate from left to right,
2. Pressand hold PAIRfor 2 seconds to enter pairing mode. LEDswill turn off for a second then start to rotate from
left to right,
3.Goto your SwitchHomepageto clickon Controllers, t hen clickon ChangeGrip/Orderandwait for controllerto
sync up LED will become solid when connection is successful.
4. Controllerwill auto reconnect t o yourSwitchwith the press of START onceit hasbeenpaired
• STAR button Switch screenshot button, Home button = Switch HOME button.
Android
1. PressSTART+Bto turn on the controller, LED 1will start to blink.
2.Press and hold PAIR for 3seconds to enterpairingmode.LED will rotatefrom left to right.
3. Go to your Android device's Bluetooth setting, pair with (8Bitdo SF30 prol or (8Bitdo SN30prol. LEDwill become
solid when connection is successful.
4. Controller will auto reconnect to your Android device with the press of START once it has been paired
• USBConnection: connect the controller to your Android device via USBCable after step 1.
Windows
1. PressSTART+Xto turn on the controller, LEDs1, 2 will start to blink.
2. Pressand hold PAIRfor 3 seconds to enter pairing mode. LEDswill rotate from left to right.
3. Go to your Windows devices Bluetooth setting, pair with [8Bitdo SF30 Prol or (8Bitdo SN30 Pro). LEDwill become
solid when connection is successful.
4. Controller will auto reconnect to your Windows device with the pressof START once it has been paired.
• USBConnection: connect the controller to your Windows device via USBCable after step 1.
O macos
1. Pressand hold START+A for 1 second to power on the controller, LEDs
2. Pressand hold PAIRfor 3 seconds to enter pairing mode. LEDswill rotate from left to right.
3. Go to your macOS device's Bluetooth setting, pair with [Wireless Controller}. LED will become solid when
connection is successful.
4. Controller will auto reconnect to your Windows device with the press of START once it has been paired.
• USBConnection: connect the controller to your macOS device via USBCable after step 1.
Turbo function
1. Hold the button you would like to set turbo functionality to and then pressthe STAR button to activate turbo
functionality.
2. HOME LED will blink when turbo functionality has been applied successfully.
3. All buttons with Turbo functionality activated will cause the HOME LEDto blink, showing you that Turbo
functionality isactive on that button.
4. To deactivate turbo function, hold the button with turbo functionality activated pressthe STARbutton to
deactivate turbo functionality. The HOME LEDwit' no longer blink if you have successfully disabled turbo
functionality.
• Analog sticks are not included.
• This does not apply to Switch.
Battery
Status
Low battery mode
Battery charging
Battery'ully charged—w
• Built-in 480 mAh Li•on with16 Hours Of play time.
• Rechargeable via its USB•Ccable with 1- 2 hour charging time.
• Battery charging time might vary depending on the environment the controller is exposed to.
@ Power Saving
1. Sleep mode 1minute with no Bluetooth connection.
2. Sleep mode - 15 minutes with Bluetooth connection but no use.
3. PressSTART to wake up your controller.
(D Support and firmware upgrade
• Please visit http://support.8bitd0.com for further information and additional support.
Pro
Manual
START
c
R3
Home
Right Joystick
the controller.
will start to blink.
LED Indicator
POWER LED blinks
POWER LEDstays solid
POWERL