ADAMEX DELTA Bedienungsanleitung Seite 16

CAUTION! Never ride your pram with the parking device on.
SHOCK-ABSORPTION
The pram is provided with the cushioning spring, whose hardness
can be adjusted by means of a special switch (fig. 12).
MOUNTING AND DISMOUNTING OF THE CARRYCOT
CAUTION! Before proceeding with the using of pram, make sure
that the carrycot is mounted correctly and locked on both sides of
the pram.
CAUTION! Do not fold the pram chassis when the carrycot is
mounted on it. The carry cot can be mounted on the pram chassis
facing forward or rearward to the direction of the travel. In order to
mount the carry cot on the pram chassis, insert the hitches into the
slots on both sides of the chassis until an audible click is heard.
In order to remove the carry cot from the pram, get hold of the
hitches on both sides of the carry cot, press the longitudinal push
buttons located there, and while holding them pressed, pull the
carry cot upward (fig. 13).
ADJUSTMENT OF THE BACKREST OF THE CARRY
The carry cot backrest adjustment mechanism is located under
the carry cot from the side of the bumper. In order to lift the
backrest press and turn the mechanism to the left and in order to
lower the backrest, press and turn the mechanism to the right (fig.
14).
In order to lift the backrest pull and turn the mechanism to the right
and in order to lower the backrest, pull and turn the mechanism to
the left (fig. 14).
The DELTA stroller does not have an adjustable bassinet
backrest.
CARRYCOT CANOPY
The carry cot is equipped with the permanently fixed canopy. In
order to change its position, press the push buttons on both sides
of the canopy at the same time and select the required angle (fig.
15). The canopy is fixed to the top of the carry cot by means of a
zipper. The canopy is equipped with the handle that is used to
transfer the empty carry cot (without your child) and with the
folded sun roof. The canopy is equipped with the handle that is
used to transfer the carry cot and with the folded sun roof. To open
the large ventilation window in the canopy, the zipper must be
undone. Another large ventilation window is located in the head of
the carrycot. To open it, the lock must be undone (fig.16).The
ZICO, VASCO, and DELTA models feature an additional
ventilation window at the front of the bassinet, which can be
unzipped.
CARRYCOT COVER
The cover for the carrycot can have a ventilation mesh panel,
opened by means of zips (fig. 17).
The carrycot is equipped with a cover, which is fastened with a zip
(fig. 17). Zips in the cover allow the child to be put in and taken out
of the pram without removing the cover. The canopy is equipped
with the handle that is used to transfer the empty carry cot (without
your child) and with the folded sun roof.
MOUNTING AND DISMOUNTING OF THE SPORT SEAT
CAUTION! Before proceeding with the using of the pram, make
sure that the sport seat is mounted and locked correctly on both
sides of the pram.
In order to mount the sport seat on the pram chassis, fit its hitches
into the slots on both sides of the pram (fig. 19a). The locking is
automatic. In order to dismount the sport seat, get hold of the
hitches on both sides of the sport seat, press the longitudinal push
buttons located there and pull the sport seat up (fig. 19a). For
models with 'waiting' adaptors, press the buttons on both adaptors
and lift the whole sport seat (fig. 19b). The locking is automatic.
ADJUSTMENT OF THE SPORT SEAT BACKREST
In order to lower the backrest, press the button at the back of the
sport seat and adjust the required position (fig. 20a or 20b). We
raise it by lifting it to the required position (fig. 21).
COT
CAUTION! While adjusting the sport seat backrest, pay particular
attention to the hands and head of the child.
CAUTION! Before adjusting the backrest of the sport seat, make
sure that the adapters on both sides are positioned downwards
(page 7 fig. A).
CAUTION!
ATTEMPTING TO UNFOLD THE SEAT BY FORCE MAY
RESULT IN DAMAGE.
CORRECT UNFOLDING OF THE SEAT - PAGE 7.
A1. Clip the seat into the chassis.
A2. Tilt the seat as far forward as possible.
A3. Pull the lever, and while holding it, adjust the backrest until it
reaches an angle of 90o. You will hear a "click"-A4.
Move the bumper into the indicated position until you hear the
"click"- A4.
SPORT SEAT CANOPY
The sport seat is equipped with the removable canopy. In order to
dismount it, insert its hitches into the handles intended for this
purpose on both sides of the sport seat chassis (fig. 22).
To remove the canopy, press the lock button and slide the hitches
off the slots.
There is a ventilation window on top of the canopy, which closes
with a flap (Figure 23).
The canopy of the pram seat can be enlarged by pulling back the
zip. This gives us access to the ventilation window (fig. 24).
ADJUSTMENT OF THE SPORT SEAT BOOTH
To change the position of the booth pull its handle forwards or
backwards (fig. 25).
SPORT SEAT COVER
The seat is fitted with a cover that is fastened with snap fasteners
to the inside of the seat sides (fig. 26) and to the railing with a zip
(fig. 27).
To change the position of the footrest, press the buttons on the
sides of the footrest (fig. 28) and, while holding them, set the
desired position (fig. 29).
The sport seat is equipped with a tilting safety bumper (fig. 30).
We mount it by inserting its hitches into the slots intended for this
purpose on both sides of the sport seat. In order to remove the
bumper, press the push buttons on the outer side and take out the
bumper from the slots (fig.30).
CAUTION! Always use the bumper together with the crotch strap,
when the child is placed in the sport seat.
CAUTION! Always use the safety belts when the child is placed in
the sport seat. The pram is equipped with 5-point safety belts.
After placing the child in the sport seat, fasten the belts, pressing
their forks into the central clasp (fig. 31a), and then tighten the
belts in buckles. To unfasten the belts, press the button on the
buckle and pull out the shoulder strap hitches (fig. 31b).If a
magnetic buckle is used, press the buttons on the sides of the
buckle to unfasten the straps. Then, detach one half of the base
from the other (Fig. 31c). To fasten the straps, follow the steps in
reverse order (Fig. 31d). Installation of harness straps. In order to
fit the belts, pull the rectangular stopper sewn up at the end of
each belt through the appropriate holes in the upholstery and the
plastic shell of the seat, and then pull the belt to check whether it
has been fastened properly (fig. 32a) or as shown in the figure
(32b), where the covering panel must be dismantled first.
CAUTION! Before adjusting the backrest of the sport seat when it
is not clipped into the frame, make sure that the adapters on both
sides are positioned downwards (page 7 fig. A).
ATTEMPTING TO UNFOLD THE SEAT BY FORCE MAY
RESULT IN DAMAGE. CORRECT UNFOLDING OF THE
SEAT - PAGE 7.
A1. Clip the seat into the chassis.
A2. Tilt the seat as far forward as possible.
A3. Pull the lever, and while holding it, adjust the backrest until it
16
FOOTREST
BARRIER
SAFETY BELTS
CAUTION!