Intended Use; Safety Instructions; Initial Operation - Kaiser Fototechnik Rb 5240D Bedienungsanleitung

5269Bedien_0525.qxp_5269edien 16.05.25 13:44 Seite 5
ENGLISH
(1) PL 40D panel light
(2) Vertical arm
(3) Articulated joint base
(4) Cable clip
(5) Fastening screw for vertical arm
(6) Fastening screw for angle guide
(7) Angle guide
(9) Fastening screw for light
(10) Diffuser screen
(11) Control dial for brightness
(12) ON/OFF switch
(13) Mains lead
(14) Socket for mains lead
(15) Fuse holder
(16) Wing screw for swivel joint
(17) A8.4 washer
(18) Fastening screw for articulated joint base
(19) M8x16 hexagon socket screw
Prior to using your surface lighting unit, please read these
instructions carefully. Keep them safe to have them at hand
at any time. If you pass the devices on to somebody else,
always include these instructions.

1. Intended use

The RB 5240D surface lighting unit is marketed exclusively
for the purpose of illumination for image capture. It is not
intended for use in other applications.
The lighting unit is equipped with articulated joint bases for
attachment to the exe.cutive LED Copylizer (5215) or the
exe.cutive LED Illumina Base Plate (5244). Supplemented
with the 5256 clamp bases – available as accessories – it
can also be attached to boards up to 48 mm (1.9 in.) thick-
ness.
Use the surface lighting unit only as described in these in-
structions. Any other use has to be considered as not as
intended and can result in material damage or physical in-
jury. The surface lighting unit is not a toy.
Kaiser takes no responsibility for damages caused by not
intended or incorrect use.

2. Safety instructions

Please observe the following safety instructions:
WARNING!
Disconnect the devices from the mains if not in use or be-
fore cleaning.
Keep the products away from children.
Do not put the devices into operation, if housing, plugs or
cables are damaged.
Unplug the mains lead from the socket by holding it by the
plug.
Do not disassemble or modify the devices. Repairs must
only be carried out by qualified persons.
CAUTION!
Only use the lighting unit with parts designed for it.
Use the devices only in dry rooms.
Keep the devices away from water and other liquids and
from combustible materials.
Make sure that the devices are not covered during opera-
tion.
Do not use or store the devices at places with extremely
high air humidity or at extremely hot places. Keep the de-
vices away from direct solar radiation.
Let the devices cool down before boxing them.
3. Check devices and scope of supply
When unpacking the devices for the first time, please
check if the scope of supply is complete. It comprises
2 PL 40D panel lights (1)
2 Mains leads (13)
2 Vertical arms (2)
4 Cable clips (4)
2 Angle guides (7)
1 Accessory kit:
2 Articulated joint bases (3)
2 Fastening screws (5) for vertical arms
6 A8.4 washers (17)
2 Fastening screws (18) for articulated joint bases
2 M8x16 hexagon socket screws (19)
1 Hex-wrench SW6 (6 mm)
(There may be more parts in the accessory kit, but
these are not required for mounting on the Copylizer
or the illumina base plate.)
Check also, if the devices are damaged by extraneous
causes. If this is the case, do not take the devices into op-
eration.
4. Assembly
Mount the articulated joint bases (3) to the Copylizer or to
the illumina base plate and the vertical arms (2) to the ar-
ticulated joint bases (3) as shown in fig. B. Subsequently
attach the angle guides (7) to the vertical arms (2) (fig. C)
and secure them with the screws (6).
Then place the lights (1) on the fastening bolts of the angle
guides (fig. D) and secure them with the screws (9).

5. Initial operation

Make sure that the mains voltage corresponds to the op-
erating voltage given on the lights (1).
Make sure that the lights (1) are switched off: the switches
(12) have to be in the "O" position. Then connect the lights
to the mains using the mains leads (13) (fig. E) and attach
the mains leads with the cable clips (4) to the vertical arms
(2).
Switch on the lights with the switches (12). The switch
lights up when the light is switched on.
The brightness can be adjusted continuously with the con-
trol dials (11). For reproducible results, there is a scale on
the control dials.