TecTake 402999 Installationsanleitung Seite 2

STEP4
lnstall Supporting plate(6)
lnstall Control box (7)
STEPS
and Handswitch(9)
F
14
�
Distance between desktop
edge and supporting plate
should be no more than
200 mm.
lnstall desktop with screw(F), use pistol drill to tighten.
STEP6
Connect All the Cables onto the Cont rol Box(?)
10
7
9
fix
Use the cable tie(ll) to all the connection
cables on the desk to keep it clean.
3
2
lnstall(6)&(2)(3), use 5*5 wrench(C) to tighten the screws(A).
lnstall Baffle (8)
E
4
eJ
D
[!,
lnsta11(8), use 2.5*2.5 wrench(D) to tighten the screws(E).
...._--+_ Power port
.-----1- Port for cable
Handswitch--1---,
How to use handswitch
Button J
LED Display
Bottom int roduction: There are seven buttons that
" .& " ' "T" "1" ' "2" '
' M '
3
l 11 11 II II
(1) ".&." : Adjust the desk upwards
(2) "�": Adjust the desk downwards
(3) "1" : Position 1, first height position saved by the user
(4) "2": Position 2, second height position saved by the user
(5) "3" : Position 3, third height position saved by the user
(6) "M" : Height memory function
(7) "A" : Alert button to remi nd users changing posture
[ Common fault treatment ]
The following tips will help you detected and eliminate the common fault and
lf the fault you met is not listed below, please contact with your supplier. Only the
manufacturer and professionals are capable for investigating and correcting
those fault and error.
Fault phenomenon
�g;� fr��! aft�� ����2ft � l�i � �
s e l 9
a power supply
No response while pressing up
arrow/ down arrow after
connected with a power supply
Rising in a low speed
The motor not move as instructed
Go down but not go up
Downward sliding
Frequently Reposition
Overwork
CDutycycle: Max 2min on/18min OFF)
Not enough up&down height
[ Waste disposal ]
connected to
the lifting column
[ lnstruction ]
• Height A djustable Function:
Press the " •" or "'I'" button to ad just the height. The LED display shows the current height.
• Height Memory Function:
a. Press UP or DOWN button and adjust the height to the desired height. Press "M " to save the height, and
the screen will display "5-"; Press "1" , "2" , or "3" then, that is, save the height to the corresponding position
1 or 2 or 3 , which will show in the display screen as "5-1" , " S-2", or "S-3";
b. Press "1", "2" and "3" button directly to automatically adjust the memory height you saved.
• Reminder Function:
a. Press REMINDER button "A" to activate the lunction. The LED display shows" Dn"
b. Two seconds later, press the "•" or "'I'" button to adjust the reminder time only when the display
' 2.
screen llashes. The delault time ol the reminder is 45 minutes, which is shown as "�YS ". Then press
any button to save the time setup, or wait 5 seconds and system will save the time setup
automatically. Du ring the countdown, any operation will lead to a repeat starting of the timer. When
the countdown finishes, display screen will show ··�DD " the buzzer will be active with a 10-second
"DiDi ... DiDi ... DiDi " tone.
c. Within the 10-second reminder buzz, press any button to reactivate the time countdown !hat is sei
up in (b) step. II no operation du ring the 10-second reminder buzz, there will be another reminder
buzz after 5 minutes. No operation du ring the second buzz will turn oll the Long -Time Sitting
Reminder.
d. Press and hold the "A" button for three seconds to turn off the Long -Time Sitting Reminder. The
BFF
LED display shows" "
"
• Troubleshooting:
II A
a. Reset: When the LED shows "RSr" , press "'I'" button until the desk reaches its lowest height and
rebounds to stop, il means the reset has been finished.
b. When it does't work and the LED shows "E 0 1" or "E 0 2", please retry 18 mins later.
c. II the "'I'" bullon does't work, please check the cable connection and then cut off thepower lor at least
10 seconds. Reconnect to the power and press "'I'" button to start the reset process when it shows the "RSf ".
d. II all these above process are inefficient, plz contact our customer service.
� Attention
1 . Power supply: AC1 00V-240V , 5 0/6 0 HZ
2 . Service Environment: 0- 40"C
3 . Unplug the power plug belore cleaning, wipe the dust on surface with slight wet dishcloth
when cleaning, be carelul not to lel lhe drops inlo the internal parts, not loose the connector.
Method
4 . The electric box contains electronic components, metals, plastics, wires etc., so dispose of
it in accordance with each country's environmental legislation, not the general household
1.Check if all the cables be connecled weil
waste.
2.Contact your supplier or dealer
5 . Check carelully to ensure correct and complete assembly before using.
6 . Be lamiliar with all lunctions and program settings ol the product before lirst use.
1.Check if all the cables be connecled weil
7. Children are forbidden to play on the product because ol unforeseen action when playing,
2.Contact your supplier or dealer
so any dangerous consequences caused by this im proper action will not be on
1. Check ifoverloaded, max loading: 70kg;
8. Slight noise caused by the V-ribbed bell or brake system due to structure will not have any
effect on the use ol the equipmenl.
2. Conlacl your supplier or dealer
9. Corrosive or abrasive materials are forbidden to clean the equipment. Mus! ensure !hat the
1. Contact your supplier er dealer
cleaner used will not pollute the environment.
1. Reposition
10 . This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack ol experience and knowledge if they
2.Contacl your supplier or dealer
have been given supervision or instruction concerning use of the appliance in a safe way and
1. Check ifoverloaded, max loading: 70kg;
understand the hazards involved. Children shall not play with the appliance.
2. Conlacl your supplier or dealer 1 1 . Cleaning and user maintenance shall not be made by children without supervision.
1 2 . II the supply cord is damaged, it must be replaced by the manulacturer, its service agent or
1. Check ifoverloaded, max loading: 70kg;
a similarly qualified person in order to avoid a hazard.
2. Conlact your supplier or dealer
1 3 . Please make sure there is no hazard sources in your operating environment. e.g., do not
1. Restartafter suspend for 18mins while
connecling with power: lilter lhe tools around. A lways be carelul to !real lhe packaging materials in order to avoid any
possible danger, e.g. plastic bag may lead to choking hazard to children.
2. Contact your supplier or dealer:
14 . Keep the original package of the equipment if necessary in case ol the future use in
1. Press "M"and "3" together f or 3 seconds or
transportation.
more, after hearing continuous beeping for twice,
it will restore factorv seltinns
2.Contac1 your supplier or dealer
Thi s marking indicates that this p roduct should not be disposed with
other household wastes. To p revent possi ble harm to the envi ronment
- or human health from uncont rolled waste disposal, recyc le it
responsi bly to p romote the sustai nable reuse of material resou rces. To
return you r used device, please use the return and collection systems
or contact the retailer where the p roduct was purchased. They can take
this p roduct for envi ronmental safe rec yc li ng .