Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Mod. SLIM HTE/ SLIM HTE SR SYSTEM
TECHNICAL SPECIFICATIONS
- Air fitting: G 1/4" M
- Product delivery fitting (version SP): G 1/4" M
- Maximum air pressure: 5 bar (73 psi)
- Maximum product pressure (SP version): 5 bar (73 psi)
APTEST
ø
1.0
1.3
1.5
1.7
1.9
2.2
2.5
** Product flow was calculated with water, setting the recommended regulations.
fer effi-
si).
USE
e sectors
Spray guns in the SLIM HTE series have been designed for the application of colours or paints or other fluid substances.
The instrument is not suitable for use with abrasives or products containing acids or petrol of any kind.
To obtain the best results, the following instructions must be followed carefully:
1. When possible, use an air hose with a minimum internal section of ø 10 mm (0,37").
2. Make sure water, oil or other impurities are fully filtered from the compressed air used (for example, by installing a
Walcom FSRD3/4 filter unit or the most complete and efficient Walcom TD3 PRO multifunction heat conditioner).
ADVICE FOR CORRECT USE
5.9").
1. The distance between the spray gun and the surface to be painted must be set between 150 and 200 mm (5,9"-7,9").
ity.
If the spray gun is working at too low a pressure and at too high a distance, it will not perform to the best of its capacity.
2. The jet from the spray gun must always be perpendicular to the surface being painted and the paint must be applied in
horizontal strokes. Any eventual shift from this position when spraying
will result in an uneven application of the paint layer.
3. Correct viscosity of the paint is between 20 and 35 sec. Ford cup
n°4. These values depend on the application and the nozzle size
used.
SHAPE OF THE FAN
jet
Adjust the air pressure, product quantity and spray aperture
until obtaining a regular imprint as in fig. C
istruzioni WI34_18.indd 25
FEED
** PRODUCT LOAD
SP
Gravity
184-286 Gr/min. (6.5-10 oz/min.)
SP
Gravity
174-182 Gr/min. (6.1-6.4 oz/min.)
SP
Gravity
280-282 Gr/min. (9.8-9.9 oz/min.)
Suction
160-180 Gr/min. (5.6-6.3 oz/min.)
SP
Gravity
290-294 Gr/min. (10.2-10.4 oz/min.)
Suction
206-218 Gr/min. (7.3-7.7 oz/min.)
SP
Gravity
270-332 Gr/min. (9.5-11.7 oz/min.)
Suction
168-228 Gr/min. (5.9-8 oz/min.)
Gravity
394-398 Gr/min. (13.9-14 oz/min.)
Suction
275-290 Gr/min. (9.7-10.2 oz/min.)
RECOMMENDED AIR PRESSURE: 2 bar (29 psi)
At the recommended air pressure the spray gun works with at transfer efficiency superior to 65%.
- Air pressure too low
- Product viscosity too high
- Quantity of product too high
ADJUSTMENTS
- Working pressure: 2-2,5 bar (29-36 psi)
- Fan: Fully open
- Air: Fully open
- Product: 3,5-4,5 turns
FAN DIMENSIONS AT 20 cm (7.9")
22-24 cm (8.7"-9.6")
23-25 cm (9"-9.8")
27-29 cm (10.6"-11.4")
25-27 cm (9.8"-10.6")
27-29 cm (10.6"-11.4")
25-27 cm (9.8"-10.6")
27-29 cm (10.6"-11.4")
25-27 cm (9.8"-10.6")
27-29 cm (10.6"-11.4")
25-27 cm (9.8"-10.6")
- Air pressure too high
- Product viscosity too low
- Quantity of product too low
25
AIR CONSUMPTION
220-260 l/min (7.4 - 8.7 CFM)
- Regular jet
09/01/18 14.18
Werbung
