Tendercare Lorelli Bedienungsanleitung Seite 4

The manual breast pump is designed for pumping and collectingbreast
WARNING! Never use the breast pump while you are pregnant, as pumping may cause childbirth.
SAFETY TIPS
- Do not place the pump in direct sunlight or rain, near heaters or other hot appliances, in places exposed to extremely high or low temperatures,
high humidity or dust.
- Before each use, check the breast pump for signs of damage. Do not use the breast pump if it is not working properly.
ATTENTION:- For hygienic reasons, the breast pump is intended for multiple use by only one user.
- Before each use, clean, rinse and disinfect all parts of the pump.
- Only store breast milk that has been expressed with a cleaned and disinfected pump.
- Do not attempt to remove the pump body while it is attached to the breast with a vacuum. Disconnect the vacuum connection by placing a finger
between your breast and the pump funnel. Then remove the pump from the breast.
- Never use the breast pump when you are sleepy or sleepy to avoid carelessness during use.
- Never use accessories or parts from other manufacturers or those not specifically recommended by the manufacturer.
-Do not pump for more than 5 minutes without interruption if no milk is leaking. Try squeezing at another time of day.
- If the process becomes very unpleasant or painful, stop using the pump and consult your breastfeeding counselor.
- Never drop or insert any foreign bodies into the openings.
INSTRUCTIONS FOR USE
Cleaning, disinfection, storage.
Before first use, clean and disinfect all other parts of the breast pump. Clean these parts after each subsequent use and disinfect them before
each subsequent use.
- Disassemble the pump completely. Also remove the valve. Be careful when removing the valve and cleaning it. If it breaks, your breast pump will
not work properly
- To clean the valve, gently rub it between your fingers in warm water with a little liquid detergent. DO not insert objects into the valve as this may
damage it.
- Before first use, disassemble and clean the product and then put the components in boiling water for 5 minutes. This ensures hygiene.
- During disinfection with boiling water, do not allow the bottle or other parts to touch the side Of the pot. This may cause irreparable deformation or
damage to the product for which Lorelli is not responsible.
-Clean carefully before each subsequent use to ensure hygiene.
- Wash all parts with warm water and delicate detergent. Always rinse all parts thoroughly after each wash.
- Wash thoroughly and rinse all parts with clean water, including areas that may not be visible but through which the food has passed, to remove
food debris. Make sure there is no liquid left in the pacifier.
- Do not place in a microwave oven. Do not heat the product in traditional ovens, on hot plates or open flames.
- Avoid the use of sharp or abrasive materials, as this may damage the product.
- Do not clean or allow the product to come into contact with solvents or aggressive chemicals. This may damage the product.
- If you use bottle brushes, be careful not to damage the most delicate parts of the product.
- After cleaning the product, dry all parts thoroughly and store in a clean and dry place without direct sunlight and away from heat sources.
- Do not leave the pacifier in direct sunlight or heat or leave it in a disinfectant ("sterilizing solution") for longer than recommended, as this may
damage the pacifier-Note: Be sure to clean and disinfect the relevant parts Ofthe breast pump. Wash your hands thoroughly before working on
clean parts!
- Be careful, as the cleaned parts may still be hot. Only start assembling the breast pump when the cleaned parts are cooled down.
pARTS
Picture 1
1Lid transforming intobottle pad
2. Softening pad
3. Funion
4. Diaphragm
5. Handle
6. Lid
7. Clap
8. Bottle
9. Pacifier
10. Screw on the pacifier
11. Pacifier cap
ASSEMBLING THE PUMP
Picture 2
Important: Before installing the pump, make sure that all parts are cleaned and sterilized.
The graphs show in detail exactly how to assemble the pump in the correct order.
Please follow them!
Wash your hands thoroughly before mounting.
1. Place the flap at the bottom of the funnel.
2. Screw the funnel into the bottle
3. Insert the diaphragm tightly at the top of the funnel.
4. Mount the handle by first sliding it through the handle and then pressing it to the end until you hear a CLICK which is a sign of locking
CAUTION: You can adjust the suction force by changing the position of the handle relative to the diaphragm. You have 3 positions available.
Lowest position for the strongest suction, highest position for the weakest suction.
5. Apply the softening pad and lid
* These parts are designed to fit snugly. For easier assembly,simply moisten the edge of the silicone ring and / or the softening pad with water.
milk from breastfeeding women. The device is designed for one user!