Ednet Universal Benutzerhandbuch Seite 9

Set up
Batteries are not included in the delivery Make sure that fresh batteries have been inserted
correctly into your new remote control unit
Replace alhuays both batteries together and make sure to use no old and new batteries same
time If you wi not use the remote control for longer time, replace the batteries to avoid damages
of remote contro by leakage.
To make your remote control ready for use, you need to carry out one of the following steps:
A Set up by Brand Code
1 Sw'itch on the device for which you Wsh to use the remote control
(e g TV set)
2 Find the code number of your device brand in the code list (e g Lifetec 0002) from the relevant
device group (TV)
3 Press and hold the device button (e g TV) for three seconds
Release the device button as soon as LED lights up, now it is in set up
mode
4 Enter the 4-digit device code (e g 0002 for Lifetec TV) within 10 seconds
made within 10 seconds, the set, up mode is automatica ly terminated
5 The LED turns off if the remote accepts the code Ifthe LED flashes three times, that means
the code may be wrong, and the remote control remains in set-up mode, enter the correct code
from the list again in good time
6 Check the function of the buttons on remote control
another 4•digit device code (eg
to 6 until all the basic functions operate correctly
Note: Exit the set-up mode by presslng the device button, or the set up
mode is automatically terminated if no button is pressed for 10 seconds
B Set up by Automatic Search
1 Sv,'itch on the device that you like to control If it is a VCR insert a cassette
2 Point the remote control at your device
the LED turns on and please still keep pressing the device button for about two seconds until
LED start flashing,
button
3 The "Volume+" signal is automatically transmitted from the remote control to the device (code
scan) As soon as the volume of the device (e g TV) changes, immediately press device key
to stop the Automatic Search
4. If the device you are searching for is a CD player, Tuner, TAPE, or AUXI Po•wer signal is
automatically transmitted from the remote control to the device As soon as the device turns
off, press device key to stop the Search And you need to turn on the device by Pov-,er button
before you check other button function
5 Check the function
(i e the search cannot be stopped at the correct time) or the majority of the buttons do not
function correctly, restart the search (see steps 2 to 4) to find a suitable code If the majorty of
the buttons function correctly, set- up has been successful
TV) to save the code and to terminate the set-up mode
C Setting up by Manual Search
1 Sw'itch on the device that you like to control If it is a VCR, pease inserta cassette
2 Point the remote control at the device Press and hold down the device button (e.g TV) for 3
seconds The LED lights up and the remote is in manual set-up mode, release the device
button now
3 Press the "Volume*"
4 As soon as the volume of the device (e g TV) changes or the device turns off, check whether
the other buttons on the remote control function correctly
not function correctly, press the Volume+
code ( manual search is continued, see steps 3to 4)
If the majority of the buttons on the remote control functions correctly, save the code by
pressing the device button ( e.g TV) to terminate the manual search
Note: The Manual Search is automatically terminated if no entry occurs during 30 seconds
period
0015...) from the list under the same brand Repeat steps 3
that means it is in Automatic Search now and you can release device
of the other buttons
button approx every 1 5 seconds
If it does not function
Press the device button (e g. TV) for three seconds,
on the remote control
approx every 1 5 seconds to initiate the reactive
8
If an entry is not
If none of the buttons
Re-press the devlce button (e g
f the majority of the buttons does
correctly, try
function