Nobels CHO-mini Digital CHORUS Bedienungsanleitung

CHO -mini
TM
Digital CHORUS
Owners Manual
English
Specifications
Power: stabilized and filtered power supply 9 Volts DC (optional)
Power connector: 2.1 mm / negative center
Consumption: less than 100 mA
Input impedance: 1 M Ohm
Output impedance: 10 K Ohm
Max. input level: 6.6 dBu (1 kHz - 1% THD+N)
Dynamic Range: 106 dB (w/o effect through DSP Buffer)
DSP Processing:
48 kHz / 32 bit - A/D D/A Sampling Rate 48 kHz / 32 bit
Controls:
Rate, Width, Mix, („GitD" pointer knobs)
Switches:
Mode, Bypass, Mono-Stereo Signal, On/Off (Tap Tempo)
Jacks:
DC, Input TRS 1/4" (6.3 mm), Output TRS 1/4" (6.3 mm)
Indicator (LED):
1x Multicolor LED: (On/Off, Mode and Tap Tempo)
Chorus 1:
LED = green
Chorus 2: LED = red
Flanging: LED = blue
Mounty-P: 4x fold-out Mounting Plates
Dimensions (cm): 9.4 (L) / 4.8 (W) / 5.0 (H) unit
Weight (gr.): 210
Specifications are subject to change without notice!
* This pedal is optimized for stabalised power supply 9 V DC.
** Hum will occur when using unstabilized power supplies!
Power supply specifications: see imprint on bottom of the unit.
Waste Electrical and Electronic Equipment labeling:
In the European Union, do not discard this product as unsorted municipal waste. Contact your local
authorities or send it back to the Nobels distributor.
Nobels BK UG
Suederfeldstrasse 35 - 22529 Hamburg/Germany
Email contact: support@nobels.com
More information: www.nobels.com
20250109MSA
Welcome to the Nobels family!
The Nobels Chorus pedal CHO-mini combines a great sound selection of legendary chorus with practical
and simple switching as well as desired application options (like TAP-Tempo) in a space-saving metal
housing. Plus those little Nobels Extras like fold-out Mounty-P mounting plates or "Glow in the Dark" point-
er knobs. We hope you enjoy using this pedal!
RATE Control:
This potentiometer regulates
the speed of the modulation.
OUT Jack:
The output to the
amplifier, effects unit, etc. The
socket can be operated in
mono and also in stereo.
MIX Control:
This control regulates the
mixing ratio and proportion of
the guitar signal to the effect
signal. 12 o'clock position
would be a mix of 50/50%.
SWITCH:
Switches the device on/off
and also controls the tempo
(rate) by 'rhythmic tapping'
The tap tempo mode is
reached by holding the button
(approx. 2 seconds).
* **
Mounty-P:
4x fold-out Mounting Plates.
BF/TB Switch:
Selector switch for
true- or buffered
bypass.
Power supply socket: 9 Volts DC.
Mode:
Chorus 1- Homage to an old, analog Chorus.
Chorus 2 - Reproduction of a classic analogue Chorus/Vibrato pedal.
Flanging - Chorus Variation with Flanging.
Mono / Stereo operation - how should the switch be set?:
Guitar or mono effect signal in > mono out = mono
Guitar or mono effect signal in > stereo out = mono
Stereo signal in > stereo signal out = stereo
In stereo mode, a stereo jack plug or a Y-cable must be used in the input
and output.
Important notes
Avoid using this unit in extreme humidity, heat or dusty environment!
WIDTH Control:
Sets the desired depth of the effect
signal.
MODE Switch:
Here you can switch between a selec-
tion of three different chorus types. See
below for a description.
IN Jack:
For connecting your guitar, another
instrument or an effects unit. The
socket can be operated in mono and
also in stereo.
LED:
The LED indicates the status and
mode of the effect device. LED lights
up = device on. Green = Chorus 1 /
Red = Chorus 2 / Blue = Flanging.
In tap tempo mode, the speed is
indicated by flashing.
Mono-Stereo Switch:
Selector switch between
mono or stereo operation.