Werbung
Verfügbare Sprachen
Verfügbare Sprachen
LogiLinke
WZ0015
Network
Cable
for RJ45,
RJI 1/12
BNC
Package Contents
Main
Tester
Unit
xl
Remote
Unit
xl
BNC Adapter Cables x2
BNC Male/Male Adapter xl
RJ45 to RJII Adapters x3
User
Manual
xl
> Safety Instructions
put the device always on a stable and straight surface It Will damage the device if it falls
Don't place the device into direct sunlight or in places With high temperature. This Will damage the
device
or shorten
its average
lifespan
Don't place it near heat sources like radiators or other heat producing devices
Don't expose the device to water, moisture or high humidity
Don't place it in the bathroom
or the kitchen
near a sink. Avoid direct contact With water.
Don't try to open the device
prior to the first use Ofour product make a backup Ofyour data
In the case Of improper
use, we are not liable for any loss Of data.
In any case, liability for loss Of data is limited to the effort that is necessary to restore from existing
backup copies
Congratulations
on the purchase Of WZ0015!
Please read the manual and safety Instructions before using the product for the first time Otherwise
damage may result
According
to the European
WEEE directive.
electrical and electronic equipment
waste
Its components
must be recycled or disposed apart from each other. Otherwise contaminative
substances
can pollute our environment
You as a consumer are committed by
to dispose electrical and electronic devices to the producer, the dealer,or
public collectingpoints at the end of the devices lifetime for free Particularsare regulated in national right Vhe symbol
on the product. in the user's manual.
or at the packaging alludes
application.
arai waste disposal of used devices you achieve an important
The Cé
confirmed that this product meets the main requirementsOfthe Directiwg2014\30/EU Ofthe European
Parliament
and the Council of Europe concerning
telecommunications
users and of electro-magnetic
interference
compliance
by the manufacturer
A Introduction
WZ0015 can easily read the correct pin configuration of 10Base-T cable, IOBase-2 cable, RJ45/RJ11
modular cables, 25M, TIA-56BA/56BB and Token Ring cable etc by comparing one transmitting end to
the corresponding receiving end. With the remote kit it can test cable installed far away either on wa
plate or patch panel It is easy to verify the cable continuity, open, short and cross connect
Lt's affordable, so you can benefit the most
Specification
• Test the correct pin configuration of 10Base T, IOBase-2 Ethernet cable, RJ45/RJ11 modular cables,
25BA, TIA 56BA/56BB and Token Ring Cable etc
• Easy to read cable status and verify cable continuity, open short and miswire
• With remote kit, it can remotely test cable far away either on wal plate or patch panel
• Test the grounding
• With auto or manual
scan
• Operates with 9 Volt block battery (not included)
1 RJ45 jack
2
RJ45 jack
3
LED display for sourcing end (jack 1)
4
LED display for receiving end (jack 2)
5
Power
switch
6
LED scanning mode switch
7
Test switch for manual scan
8
RJ45 jack
9
LED display for receiving end (same as jack 2)
10 Ground LED for receiving end
11 Battery compartment (9V)
A Operation
Loopback Test
IOBase-T
Cable
Test
1 Plug one end of tested cable on sourcing of RJ45 jack and another end of tested
cable on remaining receiving RJ 45 jack
2. Slide power switch on, the upper row LEDs will start to scan in sequence if the Auto/Manual switch is
set on Auto mode, or the LED will light on pin 1 if the Auto/Manual switch is set on Manual mode.
Note: You have to make sure the battery power is sufficient. If battery fails to the power, the LEDs
will be dimmed or hold up or no light, and the test result will be incorrect.
3 Choose the Auto/ManuaI sWtch to be Auto scan mode or Manual scan mode by pressing the Auto/
Manual
switch
4 In this moment the corresponding LED indicators Ofanother row Of LED Wil light up simutaneously
5 Read out the result Of LED display.
It tells you the pin configuration
If you fail to read the result in the first run Of LED scan, you may read it again in the second run Of
LED scan, or use the manual mode and press the test switch one by one until you read the result out
UserManual
Tester
a
must not be disposed
with consumers
and hazardous
these terms
With this kind of waste separation,
share to environmental
protection.
and terminals regarding
the Safety and health of
The CE has been demonstrated
These statements
are deposited
o
6
status Of the tested cable
Loopback Test
Modular
Cable
test
Please follow up the procedures of 10Base-T Cable Test However, the LED display should be
read as the right picture
10Base.2
cable
Test
1. Plug the two attached BNC adaptor cables on both RJ45 jacks, then connect the tested cable both
ends on BNC adaptor cables
2 As to the remaining procedures, you may refer to 10Base T cable test from step 1 2 to 1 5
Note:
1) The center pin of BNC should be read on LED 1 and shielding pin of BNC should be read
on
LED
2.
BNC SHIELDING
2) As the 10Base-2 cable has only two wires, we suggest you to read the result of LED scan
by manual mode.
• Remote
Test
I Plug one end Oftested cable on the sourcing RJ45 jack Ofmaster unit and another end on the
receiving RJ45 jack Ofremote unit. If the tested cable has already installed on the patch panel or
plate, you may use the adaptor cable to solve the connector gender problem
Patch Panel or Wall Plate
2. Now, set the Auto/manual switch on Auto mode if you work test alone.
3. Read the test resu t from LED display on remote unit.
Note: The LED display on remote unit was scanned in sequence corresponding
end
of master
unit.
A Test
Result
1 Continuity. 1 234567
8
Pin 2 is cont'nued
2. Open:
1
34
8
Pin 2 is opened
3. Short 1 2345
Pin
2 and
Pin
3 are
shorted
001000000
4. Miswire:
1 2345
678
G Pin 3 and
Pin 6 are
miswired
000001000
A Warning
• This tester is not intended for use on powered circuits. Attaching this tester to a powered circuit can
result in damage to the tester or injury to the user.
• If you will not use the tester for a long time, take off the battery from battery compartment.
RJII/
RJ12
123456
12345678G
RJ45
BNC CENTER
PIN
to the sourcing
<FoId
line
Gold
line
<FoId
line
Werbung
