First Time Installation - Usb Connections; Aerial Installation; Cable Installation - Panasonic TX-39AW304 Bedienungsanleitung

Getting Started

First Time Installation - USB Connections

To Switch the TV On
Connect the power cord to the 220-240V AC, 50 Hz.
Switch the " " button on the rear left hand side to
position "|" so the TV will switch to standby mode.
Then the standby LED lights up.
To switch on the TV from standby mode either:
" button, P+ / P- or a numeric button on
Press the "
the remote control.
Press the control switch located on the left side of the
TV. The TV will then switch on.
To Switch the TV Off
Press the " " button on the remote control or press and
hold the control switch on the TV, so the TV will switch
to standby mode.
Switch the " " button to position 2 as illustrated,"
" so the TV will switch OFF.
To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched to standby mode,
standby LED can blink to indicate that features such
as Standby Search, Over Air Download or Timer is
active. The LED can also blink when you switch on
the TV from standby mode.
First Time Installation
When turned on for the first time, the language
selection screen is displayed. Select the desired
language and press OK.
On the next screen, set your preferences using the
navigation buttons and when finished, press OK to
continue.
Note: Depending on the Country selection you may
be asked to set and confirm a PIN at this point. The
selected PIN cannot be 0000. You have to enter it if you
are asked to enter a PIN for any menu operation later.
You can activate Store Mode option at this point.
This option is intended only for store use. It is
recommended to select Home Mode for home use.
If Store Mode is selected, a confirmation screen will
be displayed. Select YES to proceed. This option
will be available in Other Settings menu and can be
turned off/on later.
If Home Mode is selected, Store Mode will not be
available after the First Time Installation. Press OK
button to continue.

Aerial Installation

If you select Aerial option from the search type selection
screen, the television will search for digital terrestrial TV
broadcasts. After all the available stations are stored,
the Channel List will be displayed on the screen.
While the search continues a message will appear,
asking whether you want to sort channels according
to the LCN(*). Select Yes and press OK to confirm.
(*) LCN is the Logical Channel Number system that
organizes available broadcasts in accordance with a
recognizable channel sequence (if available).
Press MENU button to quit channel list and watch TV.

Cable Installation

If you select Cable option and press OK button on
the remote control a confirmation screen will be
displayed. Select YES and press OK to proceed.
To cancel operation, select NO and press OK. You
can select frequency ranges from next screen. Enter
the frequency range manually by using the numeric
buttons. When finished, press OK button to start
automatic search.
Note: Searching duration will change depending on
the selected search step.
Satellite Installation
If you select Satellite option from the search
type selection screen, you can set a satellite and
watch satellite channels. When you select Satellite
installation, Antenna Type menu will be displayed.
You can select Antenna type as Direct, Unicable
or DiSEqC switch.
Direct: If you have a single receiver and a direct
satellite dish, select this antenna type. After selecting
Direct, another menu screen will be displayed. Select
an available satellite and press OK to scan for services.
Unicable: If you have multiple receivers and a
unicable system, select this antenna type. Press OK to
continue. Configure settings by following instructions
on the screen. Press OK to scan for services.
DiSEqC switch: If you have multiple satellite dishes
and a DiSEqC switch, select this antenna type. After
selecting DiSEqC switch, another menu screen will
be displayed. You can set four DiSEqC options (if
available). Press GREEN button to scan all satellites
or press YELLOW button to scan only the highlighted
satellite. If you select a DiSEqC option, Search
Type screen will be displayed. Select an option and
continue.
The following options will be available:
English - 8 -