EA-ELEKTRO-AUTOMATIK EL 9080-1530 B 15U Betriebsanleitung Seite 89

TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................5
1.1.1 Retention and use ..........................................5
1.1.2 Copyright ........................................................5
1.1.3 Validity ............................................................5
1.1.4 Symbols and warnings ..................................5
1.2 Warranty .........................................................5
1.3 Limitation of liability ........................................5
1.4 Disposal of equipment ...................................6
1.5 Product key ....................................................6
1.6 Intended usage ..............................................6
1.7 Safety .............................................................7
1.7.1 Safety notices .................................................7
1.7.2 Responsibility of the user...............................7
1.7.3 Responsibility of the operator .......................8
1.7.4 User requirements .........................................8
1.7.5 Alarm signals ..................................................9
1.8 Technical Data ...............................................9
1.8.1 Approved operating conditions ......................9
1.8.2 Control panel ..................................................9
1.8.3 Technical specifications .................................9
1.8.4 Views ............................................................13
1.9 Construction and function ............................18
1.9.1 General description ......................................18
1.9.2 Block diagram ..............................................18
1.9.3 Scope of delivery .........................................19
1.9.4 Accessories ..................................................19
1.9.5 Options .........................................................19
1.9.6 The control panel (HMI) ...............................20
1.9.7 USB port type B (rear side) .........................23
1.9.8 Interface module slot ...................................23
1.9.9 Analog interface ...........................................23
1.9.10 "Share" connector ........................................24
1.9.11 "Sense" connector (remote sensing) ...........24
1.9.12 Master-Slave bus .........................................24
2
INSTALLATION & COMMISSIONING
2.1 Transport and storage .................................25
2.1.1 Transport ......................................................25
2.1.2 Storage .........................................................25
2.2 Unpacking and visual check ........................25
2.3 Installation ....................................................25
2.3.1 Safety procedures before installation and
use ................................................................25
2.3.2 Preparation ...................................................25
2.3.3 Installing the device .....................................26
2.3.4 Connection to AC supply .............................27
2.3.5 Connection to DC sources ..........................28
2.3.6 Grounding of the DC input ...........................30
2.3.7 Connecting the "Share" bus ........................30
2.3.8 Connection of remote sense .......................30
2.3.9 Installation of an interface module ...............31
2.3.10 Connecting the analog interface .................31
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
2.3.11
2.3.12 Initial commission .........................................32
2.3.13 Commission after a firmware update or a
2.3.14 Removing units ............................................32
2.3.15 Inserting units ...............................................32
2.3.16 Adding new units ..........................................33
3
OPERATION AND APPLICATION
3.1
3.2
3.2.1
3.2.2
3.2.3
3.2.4
3.2.5
3.3
3.3.1
3.3.2
3.3.3
3.3.4
3.3.5
3.4
3.4.1
3.4.2
3.4.3
3.4.4
3.4.5
3.4.6
3.4.7
3.4.8
3.4.9
3.4.10 Recording to USB stick (logging) ................51
3.5
3.5.1
3.5.2
3.5.3
3.5.4
3.6
3.6.1
3.6.2
3.7
3.8
3.9
3.10
3.10.1 Introduction...................................................62
3.10.2 General .........................................................62
3.10.3 Method of operation .....................................62
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
EL 9000 B 15U/24U Series
Connecting the USB port (rear side) ...........31
long period of non-use .................................32
Personal safety ............................................34
Operating modes .........................................34
Voltage regulation / Constant voltage .........34
Current regulation / constant current / current
limiting ..........................................................35
Resistance regulation / constant resistance 35
Power regulation / constant power / power
limitation .......................................................35
Dynamic characteristics and stability crite-
ria ..................................................................36
Alarm conditions ..........................................37
Power Fail ...................................................37
Overtemperature ..........................................37
Overvoltage protection.................................37
Overcurrent protection .................................37
Overpower protection ..................................37
Manual operation .........................................38
Switching on the device ...............................38
Switching off the device ...............................38
Configuration via MENU ..............................38
Adjustment limits ..........................................48
Changing the operating mode .....................48
Manual adjustment of set values .................49
Switching the main screen view ..................49
The meter bars .............................................50
Switching the DC input on or off ..................50
Remote control .............................................52
General .........................................................52
Control locations ..........................................52
Remote control via a digital interface ..........52
Remote control via the analog interface
(AI) ................................................................53
Alarms and monitoring .................................57
Definition of terms ........................................57
Device alarm and event handling ................57
Control panel (HMI) lock ..............................60
Limits lock .....................................................60
Loading and saving a user profile ...............61
The function generator.................................62
www.elektroautomatik.de
ea1974@elektroautomatik.de
Page 3