RAVAK KASKADA RONDA Montageanleitung Seite 3

ASSEMBLY INSTRUCTIONS - Shower Trays with Polyurethane
Theshowertraysareperfectly compatible withall kindsofshowerenclosures manufactured bythe RAVAK Company. I t isalso
possible to complete themwiththe enclosures ofothermanufacturers. TypePUis manufactured f ordirectassembly on a level,
firm base Werecommendcompletingt.he showertray with the siphon RAVAK.
I. Removethe top siphoncover using a flat, bluntobject and
take out the sludge trap. Usingthe shoulders on the Inside
diameter,unscrewthe siphon
2. Temporarilyplace the shower tray in its final position and
mark the positionof the siphonon thefloor.
3.-3a Make the outlet piping Ø 40 mm and prepare the
connection to the siphon It is possible to cut off parts of the
reinforcement to the maximal
necessary.,with a rotating cutterØ 40-50 mm
4. Placethe showertray in its final position again,position
the siphon correctly and mark the position of the pipe joint.
Finishthe connection oftheoutletpipesandthe bottom part
ofthesiphon.
5. Apply the silicone RAVAK PROFESSIONAL sealing
compound on the entire surfaceof the tray where it contacts
the floor. Apply the silicone compound on the tray approx.
10 mmfrom the outside bottomedge.
6. Place the shower tray in the correct position screw the
siphongently.Checkandadjustthe horizontal p ositionand
theheight f romthefloor.
MAINTENANCE
When maintaining the shower bath, only wipe the painted parts, glass and plastic. Use a fine cloth and normal household
detergents. Never use any abrasive pastes, dissolvents, acetone or detergents and desinfectants, that contain chlorine. The
manufacturer is not responsible for damage caused by inappropriate use, installation or maintenance of the product The
manufacturer is entitled to continuous innovation of the product. For all other informationconcerning the installation, use and
maintenanceask your salesperson.Theguaranteeis 24 monthsfrom the date ofsale
The manufacturer recommends: RAVAKCLEANER - works to remove old and dried-on debris from glass surfaces, shower
frames,enameland acrylicbathtubs,washbasins and watertaps; RAVAKDISINFECTANT - is a specialpreparation with
considerableanti-bacterialand anti-fungal effects
Ecologically d ispose ofthepackaging materials andaftertheservice lifeoftheradiatorisfinished, p roperly dispose oftheradiator
as well.The reusablepartsof the packaging materials suchas the carton,tape andPE foil can be reusedagaininsteadof
recycling them Thenon-recyclable p artsofthe packaging andlater, t heradiatoritselfshouldbedisposed ofin asafeandproper
manner a ccording tolaw.Recycle themetalparts oftheradiator b ytakingittotheproperrecycling area
dimension 60X60 mm
Reinforcement
7. Press the tray against the floor and remove excess sealing
compound
8. Finishthe assemblyof the siphon,fit on the top cover.
Using the silicone sealing compoundarrangethe joints
betweenthe tray and floor.
9. The tiling can be a max. 5 mm over the outside edge of the
tray.
if
10. We recommend using a siliconesealingcompoundto
connect t hetraywithfinishedtilingorothersurfacesAbetter
sealfor largejoints is achieved if mortar is usedfirst and then
a silicone sealing RAVAK PROFESSIONAL compound. If
using against cement, there is the risk that the tray will not be
water resistant. It is suitable
shower trays" which is produced by the RAVAKcompany, to
achievea professionalsealing oftrays.
Later deliveries have better packaging for protection of the
trays. T hisiswhythecontact f oilisno ongerincluded
to use the "Installation set for