Docrooup DS2 Bedienungsanleitung Seite 9

AWARNING
Keep the battery away from water. Pouring water on
the battery may result in short.cicuit, overheating or
permanent d amage Ofthe battery.
AWARNING
Donot apply pressureto the cable or the plug.
Placing the cable tightened between a wall and
S
a window frame, or placing heavy objects on
the cord or the plug may result in electric shock
or fire.
Besure to insert the plug securely into a wall
socket.
Electricshock and overheating may result,
causing fire.
DOnot touch the plug with wet hands.
s
Electricshock mayresult.
Keep out Ofreach Ofchildren or pets.
s
Electric shock or injury may result'
Do not attempt to use anther maker or
model's charger to charge the battery.
s
Overheating,fire or electric shock may result.
15
15
• DOnot submerge the battery. Soaking the battery in
water maycauseirreparable damage.
• DOnot use the charging plug and/or the power source
Plug when they are dirty, wet Or dusty.
Insulation failure due to moisture absorbed in the
dust may result, causing fire.
Pull out the power sourceplug and cleanit with a dry
cloth.
To remove acable froma socket,pull the plug, not the
cable.
s
Alwayspull the charging cable gently.
Donot rotatethe pedals when charging the battery
while it is mounted On the bicycle.
Thecord may twist around the pedal orthe crank,and
the damage to the plug may result. causing electric
shock or fire.
• DOnot applyvoltage over the rated value to the
charger.
S
DOnot use sockets, correctors and Other wiring
devices with a power source other than standard rated
voltage (AC110•240 v olts) power supply.
• Overheating, fire or electric shock may result,
Do not use damaged components such as
charge Case,power cord, plug etc.
Electric short short-circuit Orfire may result.
Trouble
As one or more causes of failure might lead to the failure phenomenon, you should
find out the true cause(s) and then take the appropriate
problem. In case of doubt, please consult a qualified technician for service, repairs or
maintenance.
Failure Phenomena Causes
Can not turn on the e-bike Battery is off
The Battery is out of power
Battery aging or damaged
Poor contact of display line
Failure of controller
Failure of switch
Failure of speed sensor
Pedal assist doesn't work
Rear derailleur
Gear doesn't work well
Brake caliper mismatch
Brake Disc
Brake doesn't work well
Poor contact of display line
Display doesn't light on
Can not adjust the speed Battery's voltage is too
Speed is less than low
I Okm/h Throttle governing bar is
damaged
Poor contact
controlling line
Spring failure or being
locked
e-Bike's mileage is nadequate tire pressure
•
obviously inadequate Failure of charger
after fully charged The battery cannot be ful y
charged
• Failure of controller
• Battery aging or battery
damaged
• e-Bike has not been
assembled
Too much upgrade road
Strong wind
Bad road
Overweight
Too many braking times
Temperature
Wheel hub stop running after • The connection of battery is
switching on the power loosen
• Poor contact of controlling
line
The connection
is loose or damaged
The protective board of the
battery is broken
Shooting
solution(s) to rectify the
of Failure Solutions
Turn on the battery
Fully charge the battery
Replace the battery
Reconnect the display
Replace the controller
Replace the switch
replace speed sensor
mismatch Adjust rear derailleur
Adjust brake caliper or disc
is bent Reconnect the display line
Fully charge the battery
Replace the throttle
governing bar
Replace the spring
of the
Inflate tire with appropriate
air pressure
Repair the charger
Examine and repair the
controller
Replace the controller
Replace the battery
we
Re-adjust the e-Bike
• Boost the e-Bike by
manpower
Warm the battery above CYC
(320b')
is too low
Re-connect the battery
Replace the connection
line
Replace the battery's
protective board with a new
of wheel hub
one
16
16