Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Programming
a) Entering an ID in the receiver system:
To enter a radio remote control or a number pad to the receiver system, you must
proceed as follows:
1) Keep the LERNEN (LEARN) button of the receiver unit pressed for one second
until the LED of the remote control is illuminated. (The button is countersunk in the
device. Press it using e.g. a pen)
2) The receiver is now in "LEARN" mode for 10 seconds and awaits a valid ID signal
from the radio number pad or the radio remote control key.
3) Within these 10 seconds, press the door bell button at the desired sender to be
paired with the receiver as access device once. If user codes are already pro-
grammed in the number pad, entering a user code can also be used as signal to
recognise the number pad.
4) The remote control LED goes out when the code was added.
5) Repeat this procedure for other radio number pads and/or remote controls.
b) Deleting entries from the receiver system:
If a radio remote control key or a number pad gets lost, the entire system must be
reprogrammed. To do this, delete all devices from the memory first and then enter the
desired senders again as described above.
To delete all device IDs from the memory, proceed as follows:
1) Keep the LERNEN (LEARN) button pressed for approx. 8 seconds until the remote
control LED flashes twice. The flashing LED indicates that all IDs are now deleted
from the memory.
2) To enter new radio number pads or keys to the system, repeat the procedure
"Entering an ID in the receiver system".
Operating the number pad:
1) When entering the user code of group 1, output 1 of the receiver is activated.
(unlocks door)
2) When entering the user code of group 2, output 2 of the receiver is activated.
3) When entering the user code of group 3, output 3 of the receiver is activated.
4) Press the door bell button to activate the door bell at the receiver.
Status
Signal sounds
In the programming mode ------
Entry of valid user PIN
One signal sound
Entry of valid code in
Two signal sounds
programming mode
Valid function code
Two signal sounds
Entry of invalid code
5 signal sounds
Start-up
Continuous signal sound
Signal output 1 locked
------
System reset
------
Code already saved in
One long signal sound
system
Low battery voltage
Signal sound for 10 seconds ------
Activating the programming mode of the system using the master or "DAP" code:
To activate the programming mode of the system, and if the master code was forgot-
ten, enter the "DAP" code [8] [0] [8] [0] during the start-up phase and confirm your
entry with [*] [*].
Resetting the system with the default code 9 9 9 9
To reset the system to factory settings, enter the default code [9] [9] [9] [9] and confirm
with [#].
Factory settings of the number pad:
Option number
0
1
2
3
4
5
6
LED signals
7
Yellow LED flashes once
8
every second
------
9
------
Yellow LED flashes once
------
Changing the master code:
------
Option number: [0] -> New master code: [4 to 8 digits] -> Validation: [#]
Flashes once per second
during start-up (red LED)
Yellow LED flashes fast
------
The "DAP" code is irreversible and cannot be changed through program-
ming.
To activate the start-up phase of the system, manually disconnect it from the
power supply for at least one minute.
During first installation, use the master code [0] [0] [0] [0] and confirm with
[*] [*] to activate the programming mode of the system.
To ensure the safety of the system, change the master code immediately! (To
do this, see chapter "Changing the master code!)
The system confirms the correct entry with two beeps in both cases.
If this is the case, the device is now in programming mode and the functions
described below are available.
Make sure that you really want to reset the system factory settings since all
settings except for the master code will be lost.
Parameter
"Master code"
User PINS for group 1
User PINS for group 2
User PINS for group 3
Administrator code
Visitor codes
Locking after incorrect
entry
User entry mode
Signal sounds
Background light
The master code is not a normal value and is not affected by the system
reset. The "DAP" code 8 0 8 0 and the reset code 9 9 9 9 are entered in the
system as constants and can also not be changed with programming.
If the master code is changed, the old value is overwritten.
The master code is required to allow access to the system programming
mode.
Standard function/value
not reset
Not saved - Must be programmed
Not saved - Must be programmed
Not saved - Must be programmed
Not saved - Must be programmed
Not saved - Must be programmed
Code = 1, Locking for 30 sec. after 10
incorrect entries
Code = 1, Automatic code entry mode
Code = 1, Signal sounds are partly
switched on
Code = 0, Background light off
Werbung
Inhaltsverzeichnis
