Additional Safety Information; Using The Appliance For The First Time; Start; Control - WMF MASTER SILENT HIGH SPEED BLENDER Bedienungsanleitung

replaced by the manufacturer's
after-sales service or a similarly
qualified person. Unauthorized
repairs could put the user at con-
siderable risk.
After use, clean all surfaces that
•
have come into contact with
food. Follow the instructions in
the "Cleaning and care" section.
Always unplug the mains plug
•
from the socket before remov-
ing any ingredients causing
a blockage.
Be careful when filling with hot
•
liquids (max. 80°C!) as they could
be ejected out of the appliance
in the form of a sudden burst of
steam. Only fill with hot liquids
when the appliance is switched
off!
4.3| ADDITIONAL SAFETY
INFORMATION
Only connect the appliance to
•
a properly installed grounded
socket. The mains cable and plug
must be dry.
Do not pull the mains cable over
•
sharp edges or pinch it. Do not
let it hang down. Protect it from
heat and oil.
Never pull the mains plug out of
•
the socket by the mains cable or
with wet hands.
Stop using the appliance and/
•
or pull the mains plug out of the
socket immediately if:
the appliance or mains cable is
€
damaged;
the appliance is leaking;
€
the blade is blocked;
€
you suspect the appliance is
€
defective after it has fallen or
similar.
In these cases, return the appli-
•
ance for repair.
Do not place the appliance on
•
hot surfaces, e.g. hotplates or
similar or near open gas flames,
as it could melt.
Do not place the appliance on
•
surfaces that are sensitive to
water. It could get damaged by
splashes.
Never operate the appliance
•
unsupervised.
Do not move the appliance
•
during operation and do not pull
on the mains cable.
Do not switch on the appliance when
•
the blending container is empty.
The blender must not be operated
•
without liquid.
Fill the blending container
•
beyond the MAX mark.
Do not let the appliance run con-
•
tinuously for more than 3 min-
utes. Allow the appliance to
cool down to room temperature
before you continue processing.
In the event of misuse, incor-
•
rect operation or unprofes-
sional repairs, no liability shall be
assumed for any damage. War-
ranty claims will be deemed
invalid in such cases.
20
5| USING THE APPLIANCE FOR
THE FIRST TIME
Before using the appliance for the first time,
remove all packaging and thoroughly clean the
appliance, blending containers, lid and locking
cap as well as all accessories (see chapter
"Cleaning and care").
WARNING
Be careful not to injure yourself on the sharp
blade.
The appliance is suitable for blending and
chopping foods such as fruit, vegetables and
nuts and for preparing juices, smoothies and
shakes.
The delivery scope includes two blending
containers. A blending container made of
high-quality Tritan (BPA-free) with a capacity
of 1.75 l and an ON-THE-GO bottle made of
high-quality Tritan with a capacity of 0.6 l and
a separate blade unit. Both blending containers
can be placed on the motor block, depending
on the quantity of food to be prepared.
Now fill with the ingredients. Pay attention to
the maximum filling level mark on the blending
containers.
If you fill beyond the mark, it could overflow,
depending on the consistency of the ingredients.
For frothy foods, we advise that you only fill the
jug halfway. Close the blending container with
the lid and locking cap. The blender must also
not be operated without liquid.
To remove the lid of the 1.75 l blending jug,
turn it to the right and lift it slightly. To remove
the locking cap in the lid of the 1.75 l blending
jug, turn it anti-clockwise. You can add other
ingredients after removing the locking cap.
Beware of splashes! We recommend stopping
the motor before you remove the locking
cap. When using the blender, always snap the
locking cap back into place properly.
Make sure the blade unit is securely attached
(otherwise the blending container will not
fit on the blender properly) and the blending
container and lid are in the correct position
before using the appliance.
NOTE
The motor block can only be switched on
when the blending container and lid are
correctly attached. A safety cut-out function
prevents operation without a jug and lid.
After blending, wait for the blade to come to
a standstill before removing the lid.

5.1| START

Place one of the two blending jugs on the
motor block. The large blending jug can only be
attached in one position (handle pointing to the
front right).
Turn on the motor block by pressing the ON/
OFF symbol
at the top left edge of the
display. The display lights up. The top left edge
of the display shows which of the two supplied
blending jugs has been placed on the motor
block.

5.2| CONTROL

Select your program, manual speed setting or
pulse function by turning the wheel to the
right or left. Press the wheel to confirm your
selection.
If you want to go back one level in the menu
selection, keep the wheel pressed for approx.
1 second.
To end the blending process, briefly press the
wheel, press the ON/OFF symbol, pull out the
mains plug.
21