LGB 89590 Bedienungsanleitung Seite 5

- The distance
must allow for at least 5 seconds of
travel,
89590
reversing circuits will not work oth-
RIGIDIJO@ Cableway,230V
erwise.
89591 - The distance
RIGIDUO@ Cableway,120V
must not exceed6 m (20 ft.).
- The suspensioncables must run in
the guide slots of the valley station.
THE PRODUCT The cables must not touch the bot-
tom of the slots (cable not inclined
This RIGI DUOcablewayfeatures: steep enough), nor run above the
- two cable cars with opening doors guide slots (cable inclined too
and top and bottom escapehatches steeply).
- a lower "valley" station with Bühler
motor and built-in electronic con 3. Attach the suspension cables to
trol unit the roller brackets on the gondolas.
- infinitely adjustablespeed Slide one end of the cable through
- adjustablestation stop time the small hole in the end of the roller
- an upper "mountain" station with bracket
mounting screws knot.
- suspension cables
- 18 volt AC transformer Hint: Forprototypicalappearance, t he
- overload protection circuits rollers
- paperboardstation building kit up. The gondolas should be posi-
- four skier figures tioned with the doors facing out-
- lift tickets with ticket punch ward, so passengerscan get on and
off.
THE PROGRAM 4. Loop the suspension cables over
the pulleys on the mountain
For information on the complete valley stations. Makesurethe lower
LEHMANN TOY program, see the cable runs through the guide slots in
LEHMANNTOY catalog and the LGB the valley station.
catalog. RIGI cableways are also
compatible with LGB G-scale trains 5. Lengthen or shorten the suspen-
and accessories. Sion cables until they match the
distance
PREPARATION
6. Slide the valley station away
I. Place the valley station on a from
level surface (Fig. 1). Sion the setup. Attachthe valley sta-
tion to the surface. (4 mounting
Attention! Protect the valley station screws are included.)
from moisture.
7. Connect
2. Attach the mountain station to a former. Insert the plug into socket
vertical surface (Fig. 2). (2 mount- (c) of the valley station (Fig. 4).
ing screws and 2 anchors are includ-
ed.) Attention!
8
between the stations indoor use only.
because the automatic 8. Attach the included clips to the
suspension
descending gondolas stop at the
desired location. When the clip
between the stations
touches the valley station, the motor
stops. After the pre-selected wait
time has elapsed, the cableway
restarts in the opposite direction.
Hint: If necessary,the clips can be
opened using a screwdriver.
9. Plug the transformer power cable
into a house current outlet.
cableway starts operation. To stop
the cableway, unplug the trans-
former.
and attach it with a small
OPERATION
on the brackets should face There are two controls on the valley
station (Fig. 4):
- Station stop duration (a): Usethis
control
station stop.
You can select a duration
about 5 seconds (factory pre-set)
and
and 90 seconds.
clockwise to increase the duration
the station stop.
- Speed (b): Turn the control clock-
wise to increasethe speed.
Hints:
between the stations. - If the wheel of the valley station
spins without moving the gondolas,
the suspension wires need to be
the mountain station to ten- tightened. Shorten the suspension
wires or move the valley station to
tighten the wires.
- If the motor switches
cally or changes direction prema-
the included trans- turely, the suspension wires are too
tight. Let the motor cool. Release
the tension of the suspension
wires.
The transformer is for - If the gondolas stop in mid-travel,
increasethe speed setting (control
b).
- Do not turn the valley station pulley
wires, so that the by hand. This may damage the
gears in the station.
- Instruction for assembling the
paperboard valley station building
are included with the building.
- Both the transformer and the valley
station are equipped with overload
protection circuitry.
SERVICE
Now the Attention! Improper service will void
your warranty. For quality service,
contact your authorizedretaileror an
LGB factory service station (see
Authorized Service).
Hint: Additional expert instructions
for many LGB products are available
at www.lgb.com.
Lubrication
to set the duration of the The pulley bearings on the mountain
station should
sionally with a small amount of LGB
between
MaintenanceOil (50019).
Turn the control
of
AUTHORIZED SERVICE
Improper service will void your war-
ranty. For quality service, contact
your authorized retaileror one of the
following LGB factory service sta-
tions:
Ernst Paul Lehmann
Reparatur-AbteiIung
SaganerStrasse1-5
D-90475 Nürnberg
off automati- GERMANY
Telephone:(0911) 83707 0
Fax:(0911) 83707 70
be lubricated occa-
Patentwerk
9